The Rhino Rack roof rack part # RR42MR is a confirmed fit for your 2012 Toyota Camry 4-door and weighs a total of 14 lbs.
The part # S512 weighs 14 lbs and the part # RRS512X weighs a total of 8 lbs. That would put you well within the 165 lb capacity of the # RR42MR.
Also you need to be sure to stay under the roof capacity for your vehicle listed in the owners manual. view full answer...
I recommend using the T-One Vehicle Wiring Harness # 118763 on your 2023 Toyota Camry Hybrid. This is a plug and play style harness which connects to the factory connectors for your tail lights. It will require you to run a power wire to the 12 volt battery. This provides power to the lights on the trailer so you do not put the strain on the factory tail light wiring. view full answer...
For your 2018 Toyota Camry with a naked roof and the glass roof we have the Yakima Roof Rack part numbers # Y00425, # Y28TR, and # Y06192 which is a fit for your roof configuration and as long as you don't open the roof with the rack installed you'd be fine.
Inno does not have a rack that fits your vehicle configuration. view full answer...
The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of the setup when it is loaded and ready to tow. This figure also includes the weight of any cargo behind the rear axle of the tow vehicle. I attached a help article on determining tongue weight for you to check out as well. You will want the loaded tongue weight of your setup to fall right in the middle of the tongue weight range of the system you use.
For a loaded tongue weight of 350... view full answer...
We definitely have a roof rack for your 2012 Toyota Camry. I will also say that looking at Thule was a good option and is one of my preferences for this type of thing.
So with that being said, the Fit Kit for Thule Evo Clamp Roof Rack Feet # TH145149 are specifically designed for your vehicle and will hook to the door jambs to secure the Evo Clamp Feet # TH710501 securely to the vehicle. From here you have two options. First will be the Thule SquareBar Evo Crossbars # TH712400. These are... view full answer...
Trailer hitches with 2 inch openings are typically only available for vehicles that have higher towing capacities like trucks and SUVs. For lighter duty vehicles like your 2014 Toyota Camry there are only 1-1/4 inch hitches like the Draw Tite part # 36540. Your best solution would be a new bike rack like the Hollywood Racks RV Rider # HR200Z but there are also hitch adapters like # HTAD you could use as well but these cut the capacity of the hitch they are used in by 50 percent. view full answer...
To install the Draw Tite Hitch part # 36336 on your 2000 Toyota Camry you would need to use the included install hardware that is M10 x 1.25 x 30 mm.
Or if you wanted us to send you all new install hardware for this hitch you would need part # RHK. On the product page you would enter Draw Tite as the manufacturer and 36336 as the part number and we'll ship you out all the needed hardware to install this hitch. view full answer...
Your best option would be to replace the old style of trailer connector you have on your 1991 Toyota Camry with a new wiring kit like part # C56175 that will give you a 4-way on your vehicle to match the 4-way on your trailer. Without knowing more about what kind of wiring you have on the Camry it would be very hard to figure out what you would need to do to make the kit work.
I attached a review video for this wiring harness plus an FAQ on trailer wiring for you to check out as well. view full answer...
Depending on the style of trash can you have, I do have an option for you. If your trash can has the metal bar on the front of it then this will work, if not it may be possible to add a sturdy attachment point.
First you would need to install the Draw-Tite Trailer Hitch Receiver # 36540 on your 2014 Toyota Camry. Next using a ball mount # 3593 and have a local fabricator add tabs to go around the metal bar and slightly lift it off the ground. Similar to the included picture a customer... view full answer...
There are several 3-bike trunk mount bike carriers that will fit your 2016 Toyota Camry. I have included a link to the options for you. If you are looking for the best then look no further than the Thule OutWay # TH56BV.
I have an older version of this rack and it is by far the easiest trunk mount rack I have ever used. What makes it so easy are the 2 retractable cables it uses to attach to the vehicle rather than 6 straps like other carriers.
The excess cable stores inside the carrier... view full answer...
For your 2012 Toyota Camry, you can use the Draw-Tite Trailer Hitch Receiver # 36540 along with the 48" long Curt Cargo Carrier # C18110. This is the best options to allow you to carry your Honda Ruckus moped. I also recommend tie downs # EM05710 and soft loops # 06303. view full answer...
To be honest, the SportRack Semi-Custom Roof Rack, part # SR1005 is one of our less expensive roof racks and does not come with custom brackets made specifically for your 1999 Camry as our other roof racks do. Some of the issues is that because it is a semi-custom fit, the feet do not always fit the contour of the roof. If you are planning on using the roof rack a lot I would definitely go with a custom-fit roof rack to avoid fit issues. We have not had complaints about leaking water, and... view full answer...
The Curt Class II hitch for your 2005 Toyota Camry is part # C12339 which has a 1-1/4-inch receiver opening and a 350-lb tongue weight (TW) capacity. This means that the combined weight of your 4 bikes plus the chosen carrier's weight must remain within that rating. Please also note you will need to use a stabilizing strap like # 18050 or a similar item to help absorb some of the stresses to the hitch and its attachment points when you're using the rack. If you tow you do not need the strap.
A... view full answer...
What's the distance from the center of your hitch pin hole out to the furthest point out on your rear spare? If it's less than 6-3/4 inches you could use the RockyMounts MonoRail part # RKY10007 it in the folded position and if it is less than12 inches you could use it without folding it and it will clear the spare. The RockyMounts HighNoon FC Solo part # RKY87RR would require that distance to be less than 6 inches to use it in the folded postion and 16-3/4" to use it without folding it. view full answer...
For your 2012 Toyota Camry XLE I recommend the Draw-Tite Trailer Hitch Receiver # 36540. I like the construction of this receiver cross tube better as it travels through the frame mounts rather than flush welded like the Curt # C12107.
With your Kuat bike rack having a 2" receiver mount you can either return it for a Kuat Sherpa 2.0 Bike Rack # SH12G that has a 1-1/4" receiver mount. Or you can use a Buyers Products Trailer Hitch Receiver Adapter # HTAD. With this adapter it will reduce... view full answer...
I recommend the Curt Trailer Hitch Receiver # C12343 for your 2008 Toyota Camry hybrid. This receiver is going to be the easiest to install as it is custom fit and does not require any drilling to mount the receiver.
The T-One Vehicle Wiring Harness # 118482 will allow you to control the lights on small trailers you may tow. And these can also be used with Auxiliary Lights # C53201 if you have a hitch mounted accessory that impairs the view of your tail lights on your Camry. The Mounting... view full answer...
We have great options that will work great for your tire size of 235/45-18 but what you are going to need to do is contact a Toyota dealer in the area you are in now and ask what they suggest for tire chains as they'll have a solution. The best option in terms of clearance that fits your tire size is the part # TH02230K34 which does not drape over the inner sidewall of the tire at all so clearance issues are basically non-existent. I'd show them these and see what they say. Most likely... view full answer...
The Kat's heater part # KH11813 is a fit for your 2014 Toyota Camry with a 2.5 liter 4 cylinder engine. Kat's says to use the cartridge that is behind the passenger side of the engine block as you are facing the engine with the hood popped. view full answer...
The Hopkins Plug-In Simple Vehicle Wiring Harness # HM11141775 referenced in your question is designed to add a 4-Way to the rear of your Toyota Camry to connect with a trailer. This will not work to wire up the vehicle so that its signal lights can be powered by the U-Haul truck.
There is not a custom flat towing harness like this one available for your 2004 Toyota Camry so if you wish to add wiring you will need to go with a universal kit like the excellent Roadmaster Hy-Power Diode... view full answer...
The trailer hitches like the Draw Tite part # 36336 fit both a 2000 and a 2005 Toyota Camry as this hitch fits 1992 through 2006 Camrys.
I attached an install video for this hitch for you to check out as well. view full answer...
Go To Results