Expert Answers about Newmar

• How to Remove GloLight Uni Lite without Access to Back of Light
• The GloLight Uni-Lite LED Clearance and Side Marker Light # MCL110RKB that you referenced is designed to remove by being pushed out from behind the light. Without access to the back you could try gently prying it out with a small slot screwdriver to see if that might work. Soapy water goes a long way with these grommet lights as far as a lubricant to help coax them out.
  view full answer...


• Mounting Orientation of RV Propane Gas Detector RS64FR
• The RV Propane Gas Detector, # RS64FR should be installed in the horizontal orientation. This comes with two mounting bracket options to help cover over holes such as you describe. These options are 7-1/4" long x 3-3/8" wide or the second option of 5-3/4" long x 4-1/4" wide.
  view full answer...


• How to Get to Motor of Lippert Electric Coach Steps for Replacement
• I checked the owner's manual for the Lippert Coachsteps and to get to the motor it says, "Remove the two bolts that hold the step arm collars to the drive shaft. This will allow you to operate the steps manually." I made a cut out of the instruction manual for you which shows where it says this. I have also added the directions what you will need to do in order to replace the motor; the correct part for this is the Replacement Motor for Lippert Electric Coach Step # LC301695. I have...
  view full answer...


• Adapter Needed For Furrion RV AC Unit To Dometic Interior AC System
• If you purchased the Furrion Chill Replacement RV Air Conditioner for Dometic Brisk Setup - 15,000 Btu # FR42PV it will come with an adapter cable to plug into your Dometic system. If you did not you'll need the Coleman Adapter Wiring Kit for Furrion Chill RV Air Conditioners # C-FACR15SA-A01. This adapter will allow you to plug right into the air distribution box on your Dometic system and retain the functions of your box and thermostat instead of having to replace everything with Furrion...
  view full answer...


• How Level Does the Roadmaster Anti Sway Bar Need to be For Installation?
• It's not overly critical no, ideally you'd want your Roadmaster Rear Anti-Sway Bar # RM-1139-145 to be as level as possible so if the lower hole is the closest to level then that would be the one you need to use. There are also two holes in the frame bracket hangar that can be used for additional adjustments if need be. I've included the optimal angle for install for you to reference as well.
  view full answer...


• Roadmaster Steering Stabilizer Shock Installation Orientation
• I reached out to my tech contact at Roadmaster and the shock installation of your Steering Stabilizer # RM-RBK13-RSSA does not have a proper orientation. It can be installed with either end of the shock installed to either bracket. He said whichever orientation provides better clearance from other parts is their recommendation.
  view full answer...


• Is Serial Number Needed for Registering Thule EasyFold XT Bike Rack
• I spoke with my contact at Thule regarding your Thule EasyFold part # TH903202. She stated that they aren't aware of their being a serial number on the rack in any location. The rack is manufactured in Europe so they are not aware that it has the label on the product that shows the product #, serial # and manufacture date like the U.S. products do. Otherwise, she did also state that if you are simply looking to register the rack for warranty purposes, all they really need for this is...
  view full answer...


• Does the LED Backup Light w/ Flange for Trucks or Trailers Need To Be Replaced If Water Gets Inside
• If you have water inside the LED Backup Light w/ Flange for Trucks or Trailers part # BUL11CBX then that means the seal is broken. I recommend replacing this light as not only will it affect the luminosity of the light but it is very likely to cause a short on your trailer wiring harness. The seal can be broken by tightening the screws which hold the light too tight or just wearing out over time.
  view full answer...