Expert Answers about Mazda CX-9
- Will the Curt Ball Mount 40332 Clear the Bumper on a 2019 CX-9?
- The Draw-Tite # 76020 that you have on your 2019 Mazda CX-9 will have the pin hole recessed 6 inches from the closest edge of the bumper. With the Draw-Tite Ball Mount # 40332 being 10-1/4 inches from the center of hitch pin hole to the center of ball hole, there should be no issues using these together.
If you do not have a 2 inch ball for this, I suggest going with the Curt # A-90. This is rated up to 10,000 pounds and has the needed 1 1/4 inch shank to fit the # 40332. The Curt Pin...
view full answer... - Will the Thule Gateway Pro Trunk Mount Bike Rack Fit a 2012 Mazda CX-9
- The Thule Gateway Pro # TH78VR is listed as a fit for the 2012 Mazda CX-9. The adapter bar # TH982XT is not required unless you had a step-trough type of frame since the arms of the rack move independently of each other and the rest of the rack. A traditional woman's bike frame would not need the adapter bar.
view full answer... - Recommended Anti-Rattle Device Compatible w/ etrailer Hitches
- I have a solution for you but the Draw Tite QSP anti rattle item # 63080 you referenced can only be used on Draw Tite hitches. For a similar option you will want to use the Hitch Receiver Immobilizer II item # BX88224 which can be used on etrailer hitches like the item # e87AR.
view full answer... - Thule T2 Bike Carrier Replacement Shank
- If you have a 2 inch hitch on your 2020 Mazda CX-9 and use a hitch reducer # C45770 then this shank # 753370902 for the Thule T2 will work!
view full answer... - Recommended Roof Rack for a 2023 Mazda CX-9 w/ Side Rails
- Yes, there is a set of crossbars that will fit the factory side rails of your 2023 Mazda CX-9. These mount directly to the side rails and will have more than enough capacity for a bike rack or cargo box. You will want the roof rack by Rhino Rack and it includes the following parts:
Rhino-Rack Vortex Aero Crossbars - Aluminum - Black - 49" Long - Qty 2 item # RRVA126B-2
RCL Legs for Rhino-Rack Crossbars and Pioneer Platforms - Fixed Mounting Points - Qty 4 item # RRRCL4
Rear Wedges for...
view full answer... - Trailer Hitch Receiver, Wiring and Ball Mount For Pulling a U-Haul Trailer With a 2022 Mazda CX-9
- The Curt Trailer Hitch Receiver # C13284 is a confirmed fit for your 2022 Mazda CX-9. I verified this with Curt. When we installed this on a 2020 CX-9 we found the receiver height to be 13-1/2" from the ground. I recommend the etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit # EBMK4 as its 2-3/4" rise will put you at 16-1/4" and most trailers have a 16" coupler height.
You will also need the T-One Vehicle Wiring Harness # 118278 to operate the trailer lights on the U-Haul trailer. The Mounting...
view full answer... - Recommended Trailer Hitch Receiver And Cargo Carrier For 2010 MAZDA CX-9 Grand Touring
- The Etrailer Cargo Carrier - 24"x60" - 2" Hitch - Tilting # e98874 will certainly fit into the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # 13575 that you have on your vehicle. Both the hitch receiver and the cargo carrier will work well on your 2010 Mazda CX-9. The reason the cargo carrier may show that it isn't fit for your vehicle is because cargo carriers are not vehicle-specific and are universal-fit for most trailer hitch receivers. You will not have any issue with...
view full answer... - Recommended Transmission Cooler for a 2015 Mazda CX9
- The best standard mount transmission cooler for your 2015 Mazda CX9 is the largest one you have space available for in front of your radiator behind your grill. I recommend using the Derale 19-Row Stacked-Plate Transmission Cooler Kit part # D13403 as this is a fairly large standard mount transmission cooler that features a plate and fin technology which is far superior to the industry standard tube and fin design. As long as you have 13" wide x 7-5/16" tall x 2" deep of space in front...
view full answer... - Will Yakima SkyBox NX 16 Fit on the Factory Cross Bars of a 2010 Mazda CX-9
- Yes, I checked with Yakima and the SkyBox NX 16 # Y95AV is confirmed to fit on the factory crossbars of your 2010 Mazda CX-9.
I attached a link to the installation instructions for you to check out also.
view full answer... - Cargo Box Recommendation for a 2007 Mazda CX-9 with Factory Roof rack and Crossbars
- I spoke with my contact at SportRack and she stated that the SkyLine XL cargo box SR7095, will not fit a spread of 44 inches on your 2007 Mazda CX-9. However, there are other boxes that are listed as a fit to the factory crossbars on your CX-9.
I recommend the Yakima RocketBox Pro 14, # Y07192. Yakima lists this box as a direct fit to your vehicle. It is closest in cost and size as the Explorer box. I have included a link to the installation details for you.
view full answer... - How To Find Correct Replacement Vent Cover for Dutchmen Kodiak Express
- In order to choose an exact replacement vent cover for a trailer roof vent you'll want to pull the model number off the inside of the frame under the screen. If you cannot obtain this we do offer universal covers like the MaxxAir UniMaxx Universal Replacement Lid for RV and Trailer Roof Vent part # MA00-335001 for white or part # MA00-335002 for black that should still work well.
view full answer... - Will the Thule 5 Trailer Hitch Mount Bike Rack Fit a 2009 Mazda CX-9
- In order to determine if the Thule Apex 5, # TH9026XT, will fit your 2009 Mazda CX-9, you will need to take some measurements. On the hitch, measure from the center of the hitch pin hole out to the distance required to clear the rear of the vehicle. On the apex, the distance from the center of the hitch pin hole to the back of the hub (where the rack tilts, is 7-1/4 inches.
From the hitch pin hole to the back of the rack where the arms fold it is 16 inches. If there would be interference...
view full answer... - Is There Anything to Fill Molding on 2021 Mazda CX-9 When Installing Rhino-Rack RVP Roof Rack
- Thanks for the photo, and there is nothing that comes with the rack specifically would go over the factory moldings of your 2021 Mazda CX-9 when installing the Rhino-Rack RVP Roof Rack for Fixed Mounting Points # RRRVP51.
That said, per the instructions of the # RRRVP51, after taking out the molding it will have a "window" that you can open which allows you to access the area where the rack will install, so you can then put the molding back. I've added a cut out from those instructions for you.
view full answer... - Fit of Flint Hill Goods Aluminum Cargo Carrier # FHG69ZR on 2008 Mazda CX-9
- Because a cargo carrier is not a vehicle specific item, we do not have it listed in our fitguide, which will explain why you did not find it when you ran your vehicle.
When we installed a hitch on a 2008 CX-9, we found that the distance from the hitch pin hole to the furthest rearward point of the rear bumper was between 4-3/4 and 5 inches. Since the Flint Hill Goods Cargo Carrier you referenced provides 8-1/2 inches of clearance when fom the center of the hitch pin hole, it will fit your...
view full answer... - What AirScreen XT Fairing is the Best Size for My OEM Crossbars on My 2019 Mazda CX-9?
- I did some research on 2019 Mazda CX-9 factory crossbars, and I could not confirm the length of your particular bars. However, the general rule of thumb with fairings is to purchase the fairing that covers as much as the usable crossbar length as possible. With that being said, we do have different lengths of AirScreen XTs:
- 32" long # TH62WV
- 38" long # TH72WV
- 44" long # TH82WV
- 52" long # TH22WV
As far as the ability for the fairing's ability to clamp around your factory crossbars,...
view full answer... - Trailer Hitch Receiver and Wiring Harness For a Bike Rack On a 2021 Mazda CX-9
- You are going to need to get a new trailer hitch receiver for your 2021 Mazda CX-9. The frame and body style changed in 2016 so you will not be able to reuse your current receiver. We have the Draw-Tite in a 2" # 76020 receiver tube. Based on your images it looks like you have a Yakima bike rack but I cannot tell if it fits a 2" or 1-1/4" receiver tube. You will need to measure the width/height of the tube that slides into the receiver to ensure you get the correct size receiver.
We do...
view full answer... - What is Required to Use Curt Echo Trailer Brake Controller
- To use the Curt Echo Wireless Trailer Brake Controller # C51180 your vehicle only needs 12 volt, ground, and turn signals connected to its 7-way socket. What this means is you do not need the brake signal from the 7-way.
For example, if you used a 4-to-7 way adapter such as # 30717, there will not be an output wire from the Echo to connect to, so you could simply tie that wire off, as you can see by the accompanying diagram.
Apart from that the only other thing required is that your...
view full answer... - Roof Rack, Canoe, Paddleboards, and Bike Rack Carrier for Starcraft 2401L
- For your Starcraft 2401L popup the SportRack Pop Up Roof Rack # SR1020 would be a really great option that would fit well and would allow you to carry canoes, paddleboards, and bikes like you mentioned. The length of the bars are adjustable at lengths of 80 inches, 83 inches, and 86 inches.
Then for a canoe and paddleboard carrier the LockRack part # LR54FR would work great and for a bike rack # RKY1222 would work great.
view full answer... - Class III Hitch Pictures for a 2021 Mazda CX-9
- We do have pictures of a class III hitch installed on a 2021 Mazda CX-9 and I have attached a couple of them. I recommend going with the Draw-Tite Max-Frame Trailer Hitch Receiver item # 76020 you were looking at. It is the most concealed hitch option we have for your Mazda.
The Kuat NV 2.0 Base Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Matte Black item # BA22B would be a great bike rack to go with this hitch. It can carry two bikes at up to 60 lbs apiece. I have also attached...
view full answer... - Fitment of the Rhino-Rack ROC25 # RR87MR for a 2008 Mazda CX-9 with Fixed Mounting Points
- Yes! The Rhino-Rack ROC25 # RR87MR fits your 2008 Mazda CX-9 Grand Touring with a bare roof and fixed mounting points.
view full answer...
Go To Results