The Husky 10 Composite Slider for Silver Series 5th Wheel Trailer Hitches you reference is just the slider base, not a complete fifth wheel set up. The Husky Silver Series 26K you're wanting # HT31318-31325 is no longer available on our website.
If you're open to other brands, I recommend the Curt Q24 5th Wheel # C16545-16020. This hitch has a similar capacity as the Silver Series you were inquiring about, at 24K, and will install simply by dropping into your factory pucks on your 2015... view full answer...
I would be happy to help you find a front mounted hitch for your Ford F-250 Super Duty. I recommend the Draw-Tite Front Mount Trailer Hitch Receiver Item # 65076. This is a custom fit bolt-on installation with no welding required. A complete hardware kit is included. This hitch has a 2" receiver with a gross trailer weight of 5,000 lbs, a vertical load limit of 500 lbs and a line pull of 9,000 lbs. I have attached a picture and installation video of this Draw-Tite front receiver hitch both... view full answer...
The ground you're measuring on will likely never be perfectly level, but you'll need to try to find some ground that is as level as possible. I have included a FAQ for you to check out that will assist in measuring for your rise and drop.
If your trailer is sitting too high, then you're right, you need more drop from your shank.
Since you said you measured 22" from the ground to the receiver, and 20" from the ground to the trailer, you'll be needing a WDS shank that has at least 2" of... view full answer...
You have all of the correct parts aside from the fit kit (which is for an F-150). For your 2017 Ford F-250 Super Duty you'll need the following:
54" Vortex Crossbar - # RRVA137B
2500 Series Legs - # RRRLKVAH
Fit Kit - # DK498
Fairing - # RRRF4
This fit kit is only available with 4 clamps and pads instead of just 2 like the kit you were looking at. Aside from that everything else is the same! You can use this with something like the T-Load Hitch Mounted Load Assist # RTL002 to carry loads... view full answer...
Yes, the TorkLift SuperHitch Original Trailer Hitch Receiver # TLF1002 will fit your 2004 Ford F-250 with the 6-3/4' bed.
The Air Lift LoadLifter 5000 Air Helper Springs # AL57291 you found are designed to fit with the B&W fifth wheel hitch 1105 or 1199R. If you have either of these it will work on your F-250. Otherwise the Air Lift # AL57393 is the correct kit to fit your F-250. I do recommend considering either the Air Lift # AL88291 (for B&W) or Air Lift # AL88390 as these include... view full answer...
If you're referring to the locking plates that sit on the head of the Demco Hijacker and clamps onto the pin box to lock the head to it then you'll need part # DM6171 if you have a Trailair or Rota-Flex pin box or part # DM76FR if you have a Lippert Rhino pin box. Based on your description of the pin box you most likely have the Lippert Rhino so you'd want to go with the # DM76FR. If it is a Rhino then it will should have Rhino labeled on the sides and possibly also the front. view full answer...
For your 2005 Ford F-250 the Reese Quick-Install Custom Bracket Kit for 5th Wheel Trailer Hitches # RP50026 you referrenced is not a fit for your vehicle as they were designed for newer Ford trucks.
Instead, the Reese Quick-Install Custom Bracket Kit for 5th Wheel Trailer Hitches # RP50082 is what you'd want to use assuming you already have base rails.
If you do not have base rails then the complete Reese Quick-Install Custom Installation Kit w/ Base Rails for 5th Wheel Trailer Hitches... view full answer...
Are you looking for internal or external lights? We can help you with both. For internal lights a good option is part # ILL22CHB because of how bright it is. It's an 830 lumens light which is brighter than most for sure. It's a 2 wire install so connecting it to the switch won't be an issue.
For the wire you can use part # 10-2-1 which is sold by the foot so you want to select 60 feet when ordering. then two of part # DW05705-1 fits the 10 gauge wire and should fit your battery. The rings... view full answer...
The Bulldog Gooseneck Coupler # BD0287600300 includes the inner and outer tube along with the tube pin/clip and pinch bolt. You will only need to weld this to your Gooseneck structure and provide a lock for the coupler latch if you need to secure it to your truck. We do have the AMPLock Trailer Coupler Lock # AMP69FR which will allow you to secure the trailer coupler when it is disconnected. view full answer...
You will need the Quick-Install Custom Outboard Installation Kit w/ Base Rails for 5th Wheel Trailer Hitches
Item # RP56016-53 for your Valley 5th Wheel Hitch to work in your 2015 Ford F-250 Super Duty. This is a custom fit bracket and rail kit that is compatible with both the 6 3/4' and 8' beds of that model year.
I recommend the Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector - 7' Long item # C56070 for an in bed 7-way connector. view full answer...
The Putco Chrome Window Trim that fits a 2017/2018 Ford F-250 Super Duty with a SuperCab is part # P97564 on our site. This comes in 4 pieces. view full answer...
Unless you're using a rotating pin box like the Reese Revolution/Sidewinder or the Lippert Turning Point or the front outside edges and the corners of the fifth wheel are dished in and specifically designed by the 5th wheel manfuacturer to provide proper clearance between the 5th wheel and the truck cab during turns, you'll need to use the sliding version of the B&W Companion 5th wheel hitch for the Ford Puck system which is part # BWRVK3370.
If you're using a rotating pin box such as... view full answer...
I recommend the Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers - 2" Hitch - 10" Drop/Rise - 10K item # 325-GH-315. This ball mount will give you a wide range of options for drop and extension away from the back of your Ford F-250 Tremor. I have linked a diagram detailing the dimensions. view full answer...
I contacted Forest River for specs on the outside TV supplied in your 2013 Georgetown 378XL and they were able to confirm the coach was supplied with an AC-powered unit like our 24-inch Jensen LED model # JE2417. For a mount you can use part # MAF50. view full answer...
I have a great solution for a Rhino Roof rack on your new Leer 180 shell and an attachment for hauling a canoe. I recommend the Rhino-Rack Aero Bar Roof Rack for Camper Shells item # Y02-480B. They have a weight capacity of 220 lbs, track length of 63" per side, and the cross bar dimensions are 54" long x 3-1/2" wide x 1-1/2" tall with a leg height of 3". The two RTC-style tracks with dual C-channels provide adjustable mounting points for your roof-rack legs. The tracks mount to your Leer... view full answer...
While we have not personally loaded a 16' canoe on the Buyers Products Truck Bed Ladder Rack w/ Load Stops # 3371501680 and checked the clearance with the roof on a 2019 Ford F-250 Super Duty, this is a confirmed fit for your vehicle and will work just fine.
The crossbars that your canoe would mount to do not sit on the roof, but rather 27" from the truck bed rails to the bottom of the crossbars.
Like I mentioned earlier, this ladder rack is confirmed to fit your truck, however if you... view full answer...
It sounds like you're in need of a locking hitch pin for your 2019 Ford F-250 Super Duty, and there are some really great options available. I recommend using the BOLT Trailer Hitch Receiver Lock for 2" and 2-1/2" Hitches - Codes to Ford Side-Cut Key # BL7023585, since it codes directly to your vehicle key and can be used on 2", 2-1/2" (Class III, IV, and V), and 3" trailer hitch receivers with a 5/8" pin diameter. I really like that you don't have to worry about ever losing the key to... view full answer...
The complete Rhino-Rack roof rack for your 2017 F250 Crew Cab is as follows:
-Rhino-Rack Vortex Aero Crossbars - Aluminum - Silver - 59" Long # RRVA150S-2 (or # RRVA150B-2 for black)
-2500 Series Legs # RRRLKVA
-Custom DK Fit Kit # DK498
I attached a helpful demonstration video for you to check out. view full answer...
Yes, there is absolutely a compatible 2-1/2 inch shank that will allow you to use the Blue Ox TrackPro system with your Ford F-250; here is exactly what you'll need:
- Blue Ox TrackPro Weight Distribution with Sway Control # BLU27FR
- Blue Ox Track Pro Weight Distribution Shank for 2-1/2" Hitches # BLU26FR
Apart from that you won't need anything else as the TrackPro comes with everything you need, including the 2-5/16" hitch ball. This system is rated for tongue weights between 1,000... view full answer...
Go To Results