When it comes to purchasing The Trailer Hub Assembly - 2,200-lb E-Z Lube Axle - 5 on 4-1/2 - 13 inch - 15 inch Wheels - Galvanized # 8-258-50UC1-EZ, the bearings, races, and grease seals are included but they do not come packed. Grease will need to be added for installation.
The Easy Grease Trailer Idler Hub for 2K Axles - 13 inch to 15 inch Wheels - 5 on 4-1/2 - Pre-Greased # AKIHUB-545-2-LFEZ-2K comes with everything already packed and greased.
I attached a review video link below. view full answer...
When it comes to installing a trailer hitch on your 2000 MCI 40 foot Intercity Bus we do not have a custom hitch that would fit but you can weld on The Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2-1/2 inch Receiver - 44 inch Wide # C37CR.
The trailer hitch has a maximum gross trailer weight up to 20,000 pounds and has a maximum tongue weight up to 2,000 pounds. I would recommend checking the vehicle's manual to see the proper towing capacity for your bus. The hitch as a black... view full answer...
To finish the conversion of your 4-Way to 7-Way # C57674 on your 2016 Ford Expedition you will need a Charge Line Kit # RM-156-75. This is needed as Ford did not run the additional wire for the 7-way. You will need to run this directly to your vehicle battery with the included circuit breaker. As this will always provide power to the charge line you may want to add a Relay # BL63VR so it only provides power when the ignition is switched on. This will prevent draining your battery when the... view full answer...
The correct brake controller harness for a 2004 Ford Expedition and a Tekonsha P2, # 90885, is # 3035-P just as you have referenced. It will fit on models with a factory 7-Way or factory 4-Way. If you have a factory 4-Way, you will also need to add a 7-Way using # 37185.
The wiring to make the 7-Way fully functional should be in the plug that the 4-Way is connected to under the vehicle. There are more wires coming into the plug than coming out to the 4-Way so you would need to test the... view full answer...
The brackets were custom fabricated in our shop for mounting the 6-Pin Connector # PK11608 and breakaway switch. This can be better seen in the video for the Demco SBS Second Vehicle Kit # SM99209 installed on the same 2018 Ford Expedition. I have linked the install video below along with the video for the Charge Line Kit # RM-156-25 you found. We do not manufacture these and they will need to be fabricated either by the shop installing them or by yourself. view full answer...
Yes, I would recommend getting a weight distribution hitch for your 2021 Ford Expedition when pulling your bumper pull trailer.
When using a weight distribution system for the best ride we recommend being as close to the tongue weight of your trailer when choosing the correct distribution system.
The Fastway e2 Weight Distribution w/ 2-Point Sway Control # FA94-00-0800 will work to prevent and correct your trailer sway. The sway control brackets will also help to ensure that your trailer... view full answer...
Mounting kits for grille guards like the Westin Sportsman are specific to the particular guard item and also to the particular vehicle. All such guard items confirmed to fit your 2005 Ford Expedition are shown on the linked page.
Please note that it is not possible to make a guard item fit on a vehicle for which it was not designed, even if you have the correct install kit for the vehicle.
Westin does not have a Sportsman series grille guard for your Expedition but they do have their... view full answer...
First to determine exactly what parts you need you will need to see if your 4-way flat plug is a factory plug or if the 4-way was added on. The best way to determine this is to check under the dash for the trailer brake connector. The connector will be tucked up behind the OB2 port above the throttle pedal. I have linked an installation video below for the Tekonsha Prodigy P3 Trailer Brake Controller # 90195 that shows where this connector is on your 2012 Ford Expedition.
If you have... view full answer...
We do indeed have a harness that would work for you.
The actual plug and play harness you need will depend on who manufactured the brake controller you have. I'll run through some of the major players and the part number for the compatible harness:
• Tekonsha, Reese or Draw-Tite, use # 3035-P
• Curt, use # C51322
• Hayes, use # HA81783-HBC
• Redarc, use # RED87FR
• Hopkins, use # HM47715
If your controller is from a different manufacturer or just has blunt-ended wires exiting the rear... view full answer...
In order to mount the Surco Safari Rack 5.0 Rooftop Cargo Basket - 72" Long x 50" Wide # S5072 onto your 2020 Ford Expedition's factory roof rack you will need to use Clamp-On Adapters for Surco Safari Rack 5.0 Rooftop Cargo Basket # SP1101. This will simply clamp onto the side rails.
There are several accessories that can be added to the Surco Safari Rack such as Hi-Lift Jack Carrier # SP1108, Light Mounting Bracket # SPLT100, and Spare Tire Carrier # SPST100. I attached demonstration... view full answer...
There are actually a few places the factory connection point can be for a brake controller on your 2000 Ford Expedition. While it should be in the place indicated in the video I have linked, in other Ford vehicles it is found elsewhere:
The harness will be located under the dash near the center console on most vehicles. The harness for the Ford Full Size Van is located underneath and left of the steering column. The harness for the Ford Explorer/Mercury Mountaineer is located behind the... view full answer...
When replacing an adapter that goes from a 4-pole to a 7-pole and 4-pole we have The Adapter 4-Pole to 7-Pole and 4-Pole # 37185 but we do not carry a Pollack 7 and 4 pole for your 2012 Ford Expedition.
This Hopkins adapter will convert your 4-pole on your vehicle to a 7-pole and 4-pole flat wiring for your trailer side.
The wire functions are as followed:
White - Ground
Blue - Brake
Black - Hot lead - 12 volt power supply
Purple - Auxiliary
I attached a review video below. view full answer...
Yes, installing a 7-way on your 2005 Ford Expedition would be the recommended way to install a brake controller.
You will need to start with a 4-way (if you do not have one). For that you would want the # 18252.
From there you would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video for this product as well.
For... view full answer...
Because your Expedition has a coil spring rear suspension, there isn't an air helper spring system available but we do have a helper spring option for your vehicle, though. I'd recommend the Coil Sumo Springs, part # CSS-1168R which is the only option we offer for the 2019 Expedition.
The Coil Sumo springs install between the coils of the spring, providing additional support which reduces rear-end sag when towing. It will also reduce body roll in turns view full answer...
We do have a solution for you but I'm afraid it isn't what you want to hear. Unfortunately there are no adapters that allow a hitch receiver to mount on those locations under your bumper on your 2002 Ford Expedition.
If you want to carry 2 bikes on a hitch mount bike rack then you will need to install a trailer hitch like the Curt # C13049. This gives you a 2" receiver on your Expedition that will pair perfectly with the Swagman Trailhead #S63360 . The Curt warranty does require that a... view full answer...
To install the Tekonsha P3 brake controller, part # 90195 onto your 2006 Ford Expedition you just need to add the Tekonsha Plug-In Wiring Adapter, part # 3035-P. This is a custom adapter that will allow you to install the brake controller by simply plugging one end of the adapter into the brake controller and the other end into the built-in harness beneath your vehicle's dash. No hardwiring is required.
I have included a video review for this product as well as a link to the instruction... view full answer...
Sounds like you are looking for a propane tee and extension hose for your 1991 Palomino Pop-Up.
Depending on the style of connector you need for your 1lb tank we have a few different tees and tee with hose combos that may work for you.
The Camco # CAM59143 has a 90 degree brass propane tee with 3 ports and a 12 foot long extension hose.
The Camco # CAM59103 has a propane tee with 3 ports and a 12 foot long extension hose.
The Camco # CAM59123 has a propane tee with 4 ports and a 5 foot... view full answer...
To determine if your 1995 Fleetwood Bounder is equipped with a plug-in for a brake controller, you will need to take a look up under the dash of your motorhome. If you have a plug, it will most likely be located up under the dash on the driver's side.
If your Bounder is not equipped with this plug, you will need to use our Universal Installation Kit, # ETBC7. Due to the length of your motorhome, you will need additional 10 gauge wire, # 10-2-1, which is sold by the foot.
If you are still... view full answer...
The linked article covers the process of installing a 7-way like # 37185 and/or trailer brake controller like # 90195 in a Ford vehicle such as your 2001 Expedition. The article covers the various wiring set ups that can be found on this vehicle and others. view full answer...
Go To Results