The only option we have for trailer wiring for your 2004 Ford Crown Victoria is a hardwire option like part # 46255.
Or if you didn't want to splice any wires into your vehicle taillights you could use the zero contact kit part # 119250KIT that uses sensors to detect the vehicle taillight wiring instead of having to splice into them. You will still need to run a power wire up to the vehicle battery though. view full answer...
You would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video for this product as well.
For a brake controller I would recommend the part # TK63VR. This is one our best selling brake controller because of how well it works and how easy it is to setup. It's also priced great too. view full answer...
Yes, you can order an install kit for the Curt Trailer Hitch Receiver item # C12130. You will want the Replacement Hardware Kit for Trailer Hitches item # RHK. You will want to go to the product page and where it says item number put C12130 and under the manufacturer drop down select Curt. view full answer...
The Coil SumoSprings Custom Helper Springs for Coil Spring Suspension - Front or Rear Axle Item #
CSS-1125 are not compatible with the 1998 Ford Crown Victoria. To add suspension enhancement to the vehicle I recommend the Air Lift 1000 Air Helper Springs for Coil Springs - Rear Item # AL60798. This kit allows you to adjust the air pressure in each bag to support different weight added to the vehicle up 1000lbs for better ride quality. view full answer...
I have another option for you, but the Curt Multi-Fit Trailer Hitch Receiver # C13900 you were looking at is not confirmed to fit your 2007 Ford Crown Victoria Police Interceptor.
Instead I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # 13707 which is confirmed to fit your vehicle, and is a great option for carrying a bike rack like the Thule Hitching Post Pro # TH934XTR, a cargo carrier, or even light duty towing. You will need to drill a few holes in the vehicle... view full answer...
I did not know that having a sagging back end was cause to be pulled over. I know that some areas do have restrictions on how far off the pavement a vehicle can be. So first lets look at why the vehicle is sagging. If there is nothing in the trunk or back of the vehicle to weigh it down, and you have not modified it (like cutting the springs or used a lowering kit) then there is probably a problem with the suspension.
If your 2000 Ford Crown Victoria uses rear air shocks, that could be... view full answer...
The Draw-Tite Max-E-Loader Trailer Hitch Receiver part # 41116 is a great option for a 2009 Ford Crown Victoria and what I recommend using. It will fit models with dual exhaust. There are extra steps in the instructions for for fitment on these models. view full answer...
The only solution we have for you that would give you additional power and a more aggressive exhaust tone is going to be the MagnaFlow Cat-Back system part # MF16788 which is confirmed as a fit for your 2008 Ford Crown Victoria with a 4.7 liter V8.
Adding the part # MF35212 to your current setup will lengthen the exhaust but it would not make it any louder. view full answer...
When installing a hardwire trailer wiring harness such as # C59236 you have to test the vehicle tail light wires to determine their functions using a circuit tester such as # PTW2993.
Testing the wires is required because there is no standard wire color and function code. Your 2001 Ford Crown Vic has separate turn signal wires from the brake light wires. The yellow wire on the harness goes to the left turn signal wire on the vehicle. The green wire is for the vehicle right turn signal... view full answer...
For your 1998 Ford Crown Victoria we have the Hopkins trailer wiring harness part # 46255 as a confirmed fit that is designed to work with the taillight circuitry that your vehicle has. view full answer...
For your 2003 Ford Crown Victoria I recommend the Curt hitch # 13707. This is a Class III hitch with a 2 inch receiver rated for 400 pounds tongue weight and 4,000 pounds gross trailer weight so it covers the capacity of the vehicle.
Because your Crown Vic has dual exhaust there is some slight modification to the exhaust that will be needed to install this or any hitch for the vehicle. Its actually not all that difficult and I have included a link to a video showing an example installation... view full answer...
Installation instructions for transmission coolers are pretty universal, but there are some variances between different vehicles. With that being said, I do not have specific installation instructions for a Derale Transmission Cooler # D13503 on a 2003 Ford Crown Victoria. I can offer you basic installation instructions that will apply towards your vehicle but will not be entirely specific.
The first thing you will want to do is locate the return line of your factory transmission cooler.... view full answer...
First you will need to verify the towing capacities of the 2009 Ford Crown Vic by checking the owners manual. If you already have a trailer hitch then make sure it is rated for use with weight distribution. There should be a sticker on the hitch that lists the capacities using weight distribution if the hitch is compatible. If it is not then you would want to add a different hitch such as # 13707.
This hitch is rated for 400 pounds tongue weight and 4,000 pounds gross trailer weight or... view full answer...
From my research your 2005 Fleetwood Colonial Pop Up uses 13 inch wheels with a 5 on 4-1/2 inch bolt pattern with ST185/80D13 tires. The Karrier ST175/80R13 Radial Trailer Tire with 13" Aluminum Wheel - 5 on 4-1/2 - Load Range D -Black # AM32001HWTB will work just fine with your trailer.
The 175/80R13 tires are radials for better traction and less heat buildup on the road. They will be 24.1 inches diameter with a section width of 7 inches. The factory wheel size is 24.7 inches diameter... view full answer...
Class III hitches have a higher capacity when compared to a Class I or II. Class I and II hitches are also 1-1/4 inch receiver openings, where as the Class III are 2 inch openings.
We do have a Class III hitch available for a 2004 Grand Marquis, it is part # 41116. It can pull up to 3,500 pounds weight carrying, and if you add a weight distribution system, it can pull up to 6,000 pounds. The Class I is limited to 2,000 pounds. The Class II can pull up to 3,500 pounds too, but can only... view full answer...
Sorry about the confusion. If entered your 2010 Ford Crown Victoria into our fitguide and manually inputted your 235/55-17 tires, all of these listed tire chains will technically fit your tire size, but they have not been fitted on a 2010 Ford Crown Victoria specifically.
If you are looking at the Konig Standard Snow Tire Chains - Diamond Pattern - D Link - CB12 - Size 104 # TH01221104, those will fit 235/55-17 tires. In order to make sure these chains are safe to use on your Crown Victoria,... view full answer...
First, you may not have to do anything with the exhaust because it appears that it may only affect Lincoln Town Car models. In the event that the exhaust on your PI Crown Vic is in the way of the hitch installation, the only modification is to move a hanger bracket. I have linked the instructions so you can see the possible modifications.
If you plan on doing some towing I recommend etrailer ball mount kit # EBMK4EL. It includes a ball mount, interchangeable ball set, a hitch pin with... view full answer...
We have a trailer wiring kit that was confirmed as a fit for your 2007 Ford Crown Victoria with the part # C59236 and allows you to run a wire to the battery and is confirmed to fit with your 2-wire setup. view full answer...
The # BP08-070 measures 4 inches in length. The coiled portion of the spring is 1-5/8 inches in length and 13/16 of an inch in diameter. I've provided a photo showing these dimensions. This spring is the correct length to replace your existing spring, although it might be stiffer than your existing spring. view full answer...
For a hitch for your 1993 Ford Crown Victoria Police Interceptor the etrailer hitch part # e66AR would be a great option. Then for trailer wiring the Curt kit part # C55326 is a fit and would install easily. view full answer...
Go To Results