Expert Answers about Dutchmen

• Replacement Leaf Spring Options for a 2,000 lb Trailer Axle
• Hey Estaban, thanks for reaching out! It sounds like you're needing either the 20-3/8" Long # e84SR or the 26" Long # e77SR which are both double eye springs rated for a 2,000 lb trailer axle. You'll need to measure the center eye to center eye distance of your current leaf spring when it's unloaded (the weight of the trailer lifted off of it as well) to make sure you get the correct length. I'm not seeing an order from you with us here at etrailer.com, but if you can get me your order...
  view full answer...


• Will Champion Power Equipment 200961 Fit TorkLift Lock and Load SideKick Cargo Tray for 2" Hitches
• Yes, your Champion 200961 will fit the TorkLift Lock and Load SideKick Cargo Tray # TLA7901. The inside dimensions of the tray are 21-1/4" long x 16-1/8" wide x 3-15/16" deep. The 200961 is 17.3" long x 12" wide so it won't have any problems fitting in the tray. It also weighs 39 lbs so that is well below the 200 lb capacity of the tray. The minimum height for the strap adjustment is 16-1/2" with a maximum of 18-1/2" and your generator is 17.7" tall so it will be a perfect fit all around.
  view full answer...


• Will MORryde StepAbove Work With Keystone Montana With 30" High & 28-1/4" Wide Doorway
• Hey Rick, Yep, the 3-step MORryde StepAbove RV Steps # MR68RR will indeed work for your Keystone Montana. These steps are designed for 30" to 33-1/2" ground to threshold measurements and doorways that are are 27-3/4" to 30-1/4" wide. Since you have a 30" height and 28-1/4" wide doorway you can definitely use the # MR68RR.
  view full answer...


• Recommended Roof Vent for a 2019 Keystone Cougar 5th Wheel Trailer
• The Ventline Ventadome Trailer Roof Vent item # V2092SP-25 you were looking at would definitely work based on your measurements. You may need to widen the hole slightly but it wouldn't be by much. This is our smallest size.
  view full answer...


• Total Extended Height of the etrailer Ram Square Trailer Jack
• Hi Dave, the total extended length of the etrailer Boat Trailer Jack w/ Footplate # MJSQ-2500B is 22 5/8". Retracted it measures 7 1/4" for a total lift of 29 1/8".
  view full answer...


• Can Old Thule Square Crossbars Fit 2024 Toyota RAV4 With Flush Mounted Rails
• You can use your old Thule square crossbars on your 2024 Toyota RAV4. The Thule square bars have the same dimensions as the Inno so you can use the # INXP along with the # IN33FR to mount them.
  view full answer...


• Replacement Shroud For Dometic Duo-Therm Air Conditioner With Model Number Starting 579
• Based on the information you provided this does sound like the correct Shroud # DMC69FR for your air conditioner. We do know this to fit other 579 Dometic Duo-Therm air conditioners. And when measured in our shop we found it to be 34-1/4" long, 30" wide and 10-3/4" tall. The base the cover attaches to would have the other 2" of height. If you can provide me with the entire model number I can verify this is the correct shroud.
  view full answer...


• Dimensions Of The Brophy Rope D-Ring Tie-Down Anchor # BR59FR
• Hey Greg, I've drawn up a diagram of the dimensions for the Brophy Rope D-Ring Tie-Down Anchor # BR59FR and attached it below. If you have any other questions then just let me know.
  view full answer...


• Bolt Hole Spacing for Draw-Tite Class V Trailer Hitch Receiver DT45502
• Hey Paul, thanks for reaching out! The bolt holes for the Draw-Tite Class V Trailer Hitch Receiver # DT45502 are spaced out 35-1/2" on center for the width, and then for the back to forth dimensions we're looking at 3-3/8" for the holes closer to each other (on either end) and then 7-7/8" for the middle holes. I've attached some dimensional photos for your reference.
  view full answer...


• Replacement Wheel Center Cap for 2007 Jayco Select 12HW
• The only way to find a wheel center cap that will fit is to know your wheel size and measure your pilot diameter. For example, the # AM90195 you looked at will fit 13" and 14" wheels with a 3.33" center bore. I have attached a link below to all of our available center wheel caps which can be filtered by pilot hole diameter once you have your measurement.
  view full answer...


• LED Replacement for Truck-Lite 60 on Triton Boat Trailer
• We several options with similar dimensions although none of them are an exact match to the Truck-Lite 60. The Peterson LumenX LED Trailer Tail Light # M822R-7 matches your length at 7-7/8" but is a little taller at 3-5/8" and has completely different mounting holes. We also have some Optronics lights like the GloLight LED Trailer Tail Light # STL111RFMB which are 7-1/2" wide x 3-5/16" tall so a little short on the length. All of the Optronics have mounting holes that are 7" apart while...
  view full answer...


• How to Find Correct Replacement Leaf Springs for a Pioneer BH270
• Cory in order to find the correct leaf springs for your Pioneer BH720 you're going to need to measure the spring width, the center to center eye measurement, as well as the spring seat center to spring seat center. From here I will be able to help you find the correct set of leaf springs for your trailer.
  view full answer...


• Recommended Suspension Enhancement for a 2024 GMC Canyon Pulling a Trailer
• Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you are not towing your trailer. These significantly affect the range of your suspension which can leave you with a stiff rigid feeling in the rear end. Plus if you hit a bump while there's weight on them they tend to bounce. Instead, I recommend the SumoSprings...
  view full answer...


• Recommended Solera Slide Topper For A 150" Flange To Flange Measurement
• Hi Donald, For a 150" flange to flange measurement you'll need the Solera RV Slide-Out Awning # LCV000163299. This slide topper is designed to fit 146" - 151" flange to flange measurements. Going a size larger than this could potentially sit the mounting brackets out too far to be able to mount them to the wall of the slide out. This would have roughly 3" of overhang (fabric and arms) so it's important to make sure the arms won't come into contact with anything near your slide out. To...
  view full answer...


• Width Where You Bolt Leaf Spring For Dexter Equalizer DX62QR
• The width is 2 inches where you bolt the leaf spring to the Dexter Equalizer for 1-3/4" Wide Double-Eye Springs # DX62QR.
  view full answer...


• Recommended Camper Tie Downs for a 2007 Chevy Silverado 2500HD w/ a Stock Hitch and No Board or Step
• Thanks for the information! I have a couple of options for you that I have listed below which ones you go with will be determined by the bed length of your 2007 Chevy Silverado 2500HD. 2007 Chevy Silverado 2500HD with a 6-1/2' Bed TorkLift Camper Tie-Downs - Custom Frame Mount - Front item # TLC2205 TorkLift Camper Tie-Downs - Custom Frame Mount - Rear item # TLC3205 2007 Chevy Silverado 2500HD with a 8' Bed TorkLift Camper Tie-Downs - Custom Frame Mount - Front item # TLC2204 TorkLift...
  view full answer...


• Recommended Slide Out Topper For A 138-1/2" Flange To Flange Measurement
• For a 138-1/2" flange to flange measurement I recommend the Solera RV Slide-Out Awning - 139" Wide - Black # LCV000168328. This will have approximately 2-3/4" of overhang past the slide out so you'll want to make sure that there's enough clearance on both sides of the box. If not you can size down to the # LCV000184673 and would need to play with it a bit to get it centered on the box. You'll want to pick up some butyl tape # AL28FJ to waterproof the mounting brackets as well. I've attached...
  view full answer...


• Recommended Durabilt Hammerlock Coupling Link For An Angles Safety Chain Loop.
• Hello Stephen, so the Durabilt Hammerlock Coupling Link # DU84GR is made for a 5/8" chain link and is the largest size we offer. I do not have a way to know the exact dimensions of the oval safety chain loops on your hitch, so I do suggest measuring to verify this, but I imagine the # DU84GR would undoubtedly fit. If you need a different size, they are available in the following sizes: 5/16" Chain # DU66MR 3/8" Chain # DU46MR 1/2" Chain # DU96MR
  view full answer...


• Length/Width of Yakima BaseLine FX Roof Rack Crossbars For 2019 Hyundai Santa Fe w/ Bare Roof
• Hi John; great choice going with the Yakima roof rack for your 2019 Hyundai Santa Fe with a bare roof, and the crossbars themselves are 2-3/4" wide x 1-1/8" tall for the Yakima BaseLine FX Roof Rack # Y59UV. That should allow you to clamp any accessory on them as they are standard size crossbars. To complete the set up for your' 19 Santa Fe you'll also need the BaseClip Fit Kit # Y06151 and # Y06154.
  view full answer...


• Recommended Extended Ball Mount for a Boat Trailer
• Sounds like you need an extended ball mount. The Hidden Hitch Ball Mount item # 80232 you were looking at would definitely give you plenty of turning clearance. It measures 15-3/4" from center of hitch pin hole to center of ball hole and has a 6,000 lbs capacity. Depending on your coupler size you will either need a 2" Hitch Ball item # 63845 or a 2-5/16" hitch ball item # 63847.
  view full answer...