You could use either the Yakima FullSwing # Y02465 or Thule Apex Swing XT # TH9027XT on your 2021 Chrysler Pacifica and they'd both do a great job; it's a lot like trying to choose between Nike or Adidas. In this case I recommend using the Thule Apex # TH9027XT since it's a bit lighter at 42-lbs compared to the 56-lbs FullSwing; this allows easier removal when it's not in use.
I've linked a review video of this rack for you to take a look at. view full answer...
Really and truly there's only one option for a hitch on a 2014 Chrysler 300 with the heft to carry something as robust as an electric scooter, and that's the 2 inch hitch from Draw-Tite:
- Draw-Tite Max-Frame Trailer Hitch Receiver # 76145
The # 76145 has a 4,500 lb towing and 675 lb tongue weight capacity, both of which are far ahead of what any other hitch for this vehicle can offer. Your customer will need to keep in mind they are limited by the lowest-rated factor, so they'll need... view full answer...
The wiring being stored in the trunk is pretty standard especially on passenger cars. When the wiring is closed in the trunk the rubber seals protect the wiring and the vehicle finish. You will not want to allow a large amount of extra wire to be left hanging out of the trunk or the wind could cause the wiring to rub on the vehicles finish. Find a happy medium and you should not have any problems. Keep the wires clean so that when you are towing, grime on the wires does not have a chance... view full answer...
The Curt hitch part # C12180 that you referenced does fit your 2020 Chrysler Pacifica Hybrid and does not require any additional components to install. With that said since you have a 2 inch hitch bike rack the part # C13383 would be a better option as it is a 2 inch hitch and the hitch you referenced is a 1-1/4 inch.
I attached an install video for this for you to check out as well. view full answer...
First thing you will need is a trailer hitch on your 2007 Chrysler Town and Country. For that you would want the part # 75305 for if you have stow and go seats or part # 75119 for if you do not.
You will want trailer wiring as well. For that you would want the part # 118300 to give you a 4-way. Now to convert this to a 7-way so that you can install a brake controller which will activate the brakes of the trailer you would want the part # ETBC7.
For a brake controller I would recommend... view full answer...
It sounds like your ultimate goal is to have a trailer hitch receiver and a 7-way on your 2021 Chrysler Pacifica. I will start by addressing the # HM40975-11933. This adapter is not confirmed to fit your vehicle so it is not something you would want to use even though the bracket would fit the hitch mounting point.
The Draw-Tite Max-Frame Trailer Hitch Receiver # 76046 is a great choice for your Pacifica. You mentioned it was a round hitch, but that won't make a difference aside from the... view full answer...
The Yakima FatCat EVO 6 Locking Rooftop Ski and Snowboard Carrier # Y03096, or the Yakima FatCat EVO 4 Locking Rooftop Ski and Snowboard Carrier # Y03095, will fit directly to the T-Slot of your roof rack but only with the adapting hardware kit. The necessary hardware can be found in the Aero Crossbar SmarT-Slot Kit 2 for Yakima FatCat Ski and Snowboard Carriers # Y03098. I spoke with my contact at Yakima and confirmed this hardware is what you will need to mount the FatCat to your crossbar's... view full answer...
We have several vents that might work for your Streamline trailer but nothing that is made specifically for it. I have included a link to the right to the options for you. Most of the vents require a 14-1/4 inch square opening to install the vent.
The majority of the vents have plastic lids with a few exceptions that have metal lids. Beyond that it is just a matter of the color you want: white, blue, smoke, silver, clear, and metal.
I also recommend the vent installation kit # 344270KITW. view full answer...
Two sizes and weight classes of hitch are offered for your 2008 Chrysler 300. These include several of the 1-1/4-inch Class II type and one of the 2-inch Class III type. All things being equal I suggest the 2-inch Class III hitch # 13465 from Curt since this size hitch will be more widely compatible with a range of hitch-mount accessories like bike racks and cargo carriers. An install video is linked.
All you will need to add is the hitch ball, either a 1-7/8-inch (# 19256) or 2-inch... view full answer...
Generally speaking, using a trunk mount bike rack is not a good idea while towing as it could then create turning clearance issues. There is the option of using hitch adapters and tongue mounted bike racks but these sort of things can get messy and it's hard to offer a definitive solution.
I recommend installing a hitch on the back of the trailer, the Adjustable Width Trailer Hitch Receiver part # 13703. Then, you can use a hitch mounted bike rack rated for use on trailers, the Swagman... view full answer...
To make a 7-way to 6-way square adapter will require you to get the part # 37995 to use the 6-way end and then wire up a 7-way to it like part # H20043. This will give you the adapter you would need since there isn't one already pre-made. view full answer...
The Mopar hitch for your 2012 Chrysler Town and Country couldn't sit any higher than the Curt Hitch part # 13364 would as this hitch tucks right under the rear bumper. The # 13364 will give you about 12 inches of clearance, and since there is no way an OEM hitch could sit up any higher than this one this would be your best option since it is most likely less expensive. view full answer...
I will be happy to help you out. For your 2017 Chrysler Pacifica I recommend the etrailer trailer hitch # e98903. This hitch will fit all models of the Pacifica, including both the hybrid and non-hybrid models. This is a Class III hitch with a 2 inch receiver.
Since you mentioned that you will be doing some towing I recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes... view full answer...
The Fastway weight distribution # FA94-00-0600 and the Blue Ox part # BLU45FR are very similar as the Blue Ox is essentially a replica system of the Fastway that is super popular and well established as a great and high value system.
Functionally I don't think you'd notice much of a difference but since the Fastway has been around longer and we know it's rock solid whereas the Blue Ox is newer I would lean towards the Fastway if I were making the choice. view full answer...
For an LED version of the light you sent in a picture of you'd want the part # STL22RB with the grommet part # A70GB. I also attached an install video for this for you to check out as well.
Since I am not totally sure what the other marker lights are we do have the LED part # MCL31RB which is 4 inch by 2 inch.
For a standard roof vent to fit what you have currently we have the Ventline Ventadome kit part # V2094SP-30 which has a 12 volt fan in it.
For interior lighting we have the... view full answer...
Your assumption is correct. If the distance from the ground to the top of the receiver opening on trailer hitch # 36798 is 12 inches, and the distance from the ground to the bottom of a level trailer coupler is 17 inches, you would need a ball mount with a 5 inch rise.
Ball mount # 36065 is a good option. It takes a ball with a 3/4 inch diameter shank. For a compatible 1-7/8 inch ball you can use # 19256. For a 2 inch ball use # 19258.
For trailer wiring if your 2017 Chrysler Pacifica... view full answer...
For the 235/65-17 size tires on your 2019 Chrysler Pacifica I highly recommend the Titan Chain Alloy Snow Tire Chains # TC2319. These are Class S rated chains (meaning they are designed to work with wheel wells that have limited clearance), feature a really nice color-coded system that allows for a simple installation, and the integrated tensioners maintain a snug fit around the tire. I have installed these before and can speak to their simplicity and durability.
I have attached a video... view full answer...
Congrats on nice new vehicle. I can understand you want to not damage it. If I wanted something easy, dependable, and sturdy I would not use a roof rack or a trunk rack. They are a lot of work to get installed and loaded, and then unloaded and uninstalled. I would definitely go with a hitch with a 2" receiver.
While the initial investment is higher, there are some big benefits to this method and additional opportunities besides carrying bikes. I will touch on each of these as we go.... view full answer...
I checked with Thule and all of their cargo boxes are a confirmed fit for the factory crossbars of your 2017 Chrysler Pacifica so the Thule Force XT part # TH6359B that you referenced would fit and work well. view full answer...
For your 2003 Chrysler PT Cruiser I have a solution that will allow it to carry a rolling walker at the rear of the vehicle, but you can't use truck mounted bike racks for this as they are not designed for it haven't been tested.
Instead you would need a cargo carrier like the part # C18145 to carry the walker. For a cargo net to secure the walker you would want the part # C18200.
For a hitch for the 2003 PT Cruiser that would work well with the carrier you would want the part # 24759. view full answer...
Go To Results