The correct Aries Grille Guard for a 2007 Chevrolet Tahoe is part # AA4065 which uses the Replacement Installation Hardware for Aries 1-Piece Grille Guard part # AABRKT-4065. view full answer...
The Power Gear jacks have been consolidated into a motor for the Left Jacks # LC386198 and a motor for the Right Jacks # LC89CJ. Lippert was unable to confirm exactly what side your current motors are for but assured me that these are the possible replacements for your motors based on what side they are mounted. view full answer...
We don't have a confirmed fit for a Bell bike rack. Based on the information your gave, I recommend the Locking Anti-Rattle, Threaded Hitch Pin for Swagman 2" Hitch Racks # S64027. If you don't want the lock, then you can use # P5901. These pins are 5/8 inches diameter. The bike rack manufacturers all use different threads, but your rack looks very similar to the Swagman Trailhead fixed base rack.
if that doesn't fit your rack, you may want to consider drilling out the threaded... view full answer...
The Westin Sportsman Grille Guard that fits your 2000 Chevrolet Tahoe LT is part # 40-0185. For a replacement bracket/hardware kit you can use kit # 40-018PK. Installation instructions are linked for your reference. view full answer...
Since your trailer coupler is 4-1/2-inches lower in height than the top of the hitch ball you want to use a 2-inch trunnion style shank with DROP in order for the hitched trailer to remain level. You can use Reese part # RP3215 that you referenced, or part # RP63971, both of which will give you the required drop and work with your Reese # RP66022 weight distribution system. view full answer...
We do have the replacement wiring harness for your Tekonsha Primus IQ Trailer Brake Controller # TK90160 which will allow you to install it in your 2007 Chevy Tahoe. Keep in mind there is no plug-and-play harness for your Tahoe, so the correct one will have the blunt-cut wires on the end:
- Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller # 20127
This is the exact replacement for the harness that comes with the Primus IQ so you can connect it to your... view full answer...
I am going to assume you have the Blue Ox SwayPro weight distribution hitch, and you can use the system you have now, and all you'll need to do is upgrade the spring bars. For your 10,000 lb GVWR trailer, what you will need are the following:
- Replacement Spring Bars for Blue Ox SwayPro Weight Distribution System # BXW4008
These spring bars are rated for total tongue weights between 1,000 lbs and 1,500 lbs, an since a trailer's loaded tongue weight will be in the range of 10% to 15%... view full answer...
The # 40-018PK brackets you had looked are compatible with the Westin # 40-0185 or the # 45-0180 Sportsman Grille Guard. Either of those grille guards are compatible with a 2003 Chevy Tahoe, but keep in mind that the grille guards themselves are also vehicle specific to a large degree. Unless you know for sure that the grille guard you're working with came from a 2000-2006 Tahoe, a 1999-2000 Silverado 1500, a 2001-2002 Silverado 1500 LD or a 2000-2006 Chevy Suburban, we couldn't guarantee... view full answer...
I spoke with my contact at Dexter to find the bearing and seal information on the 8-133 hub. She confirmed that the 8-133 hub uses inner bearing # 25580 and outer bearing # LM67048 with the 10-1 # GS-2125DL grease seal. These match with the hub you referenced # 8-213-5UC1. The Dexter Trailer Hub Assembly # 8-213-5UC1 will work well for you. view full answer...
We have the updated Mounting Hardware Kit # 40-018PK for your 2005 Chevrolet Tahoe, but this would be for the Westin Sportsman Grille Guard manufactured after 2006. If you are pulling this off another vehicle, try to get the purchase information from them to make sure they purchased it after 2006. view full answer...
For just the drop leg with the foot for the Stromberg Carlson # JET-3555 you would want the part # 2500-3755G and then if you need the pin you would want the part # 2500-26. view full answer...
We have the part # 7-150 which is just a tiny bit longer by 3/32 of an inch but aside from that matches the # 7-122 but is galvanized. view full answer...
Good news, I can help you find the correct replacement hardware for your Westin Brush Guard.
Depending on which Westin Brush Guard you have will determine which replacement hardware kit you will need. I have attached our brush guards that fit your 1999 Tahoe for your convenience.
If you have the Westin # 40-0085 or # 45-0080 the right kit for you is # 40-008PK. It is important to note that all brush guards are not universal but custom to each vehicle, this hardware kit will only work... view full answer...
It sounds like you need a replacement buckle that goes with the straps on your CIPA Universal Towing Mirrors - Clip On - Qty 2 # 7070-2. Although they are not sold individually, we do have the Replacement Straps for CIPA Clip-On Towing Mirrors - Qty 2 # 11952STRAP. This comes with 2 straps and 2 buckles so you will have a spare if you need one later on. view full answer...
I have a solution for you, but the Putco Element In-Channel Window Vent # P480015 is not available in a 4 piece set and are the only available set that comes in a chrome color. I recommend going with the Weather Tech Side Window Air Deflectors # WT84184 , which is a front and rear set that comes with dark tinting that still allows fresh air in while keeping the bad weather out. view full answer...
I'm sorry to hear about your cargo box! Most Thule cargo boxes like the Force XT XL # TH6358B have a 4-character key code starting with a letter (usually an "N"). Unfortunately, if there is no key code on the lock cylinder, the only other option is to drill the lock. Once the lock is removed, you can replace the lock cylinders with the Thule One-Key System Lock Cylinders # TH450200. This kit comes with 2 cylinders, 2 keys, and a change key.
If you need assistance drilling out the locks,... view full answer...
I called my contact at Fulton about the replacement wheel options for your Fulton F2 Swing-Up Jack.
The Fulton wheel, part # F6811S00 is a 6 inch wheel whereas the wheels on the Swing-Up are 7 inch diameter. The center hole diameter in the wheel is 5/8 inches and with the included bushing the center hole diameter is 1/2 inch. This wheel is 2 inches wide, so that may be a factor when trying to install these wheels on the Swing-Up jack. We do not carry direct replacement wheels for the... view full answer...
Installation brackets and hardware for grille guards like the Westin Sportsman Series are both vehicle-specific and product-specific. It is necessary to know that exact grille guard part number you have in order to determine if it will fit on your Tahoe and whether a replacement hardware kit is available to allow it to be installed on your vehicle.
The replacement hardware kit for the Westin Sportsman New Style Grille Guards that fit your Tahoe, parts # 40-0185 and # 45-0180, is kit #... view full answer...
If you have Reese hitch 44668 for your 2005 Chevy Tahoe then it is the same as Draw-Tite hitch # 75725 and uses multiple bolt sizes. It uses two Carriage Bolts 1/2"-13 X 1.75 GR 5 and four Hex Bolt M14 X 2.00 X 40mm CL 10.9. It also takes four lock washers, four flat washers, two block spacers, two conical tooth washers, and two 1/2"-13 hex nuts.
If you have 37152 or 37136 it uses four 1/2 inch carriage bolts, four 1/2 inch flat washers, four 1/2 inch lock washers, four block spacers,... view full answer...