The Table Leg # 315-DTX that comes with the Rectangular Boat Table # 315-DSH-KF is 2" OD. The ends of the tube are tapered down to 1-7/8" OD for the Mounting Brackets # 315-DTY and # JIF54FR. view full answer...
The Rectangular Boat Table - Surface Mount - 28" x 16" # 315-DSH-KS has an ivory color so it's an off-white but not quite cream-colored.
The base that comes with it is installed by putting mounting screws through the base into the floor - it doesn't use a twist and lock feature like you mention your current one using.
If you're wanting a table with a lower-profile base the I recommend checking out the Rectangular Boat Table - Recessed Flush Mount # 315-DSH-KF instead, which is the exact... view full answer...
The part # 315-DTX is a replacement part for the Rectangular Boat Table # 315-DSH-KF which is designed to fit a 3 inch hole and comes with a table top. We don't have a way to use the # 315-DTX without the base. view full answer...
The outside diameter of the Table Leg # 315-DTX for the Octagonal Boat Table # 315-DSI-KS is 2" in diameter. The end of the leg does taper down to 1-7/8". view full answer...
The Rectangular Boat Table # 315-DSH-KF can be put up and taken down each time. The only thing that gets bolted down is the flush-mount bracket that the pole goes into on the boat floor.
The actual table post is pushed into the flush-mount and the top is then pushed onto the post. There are no additional bolts or screws for those parts. I have seen some people say that the fit can be rather snug, making it difficult to remove by hand at times, so that is something to keep in mind. But... view full answer...
We do not have just the tabletop available for the Octagonal Boat Table # 315-DSI-KS. The only way to get the top is with the whole # 315-DSI-KS set. view full answer...
I've gone ahead and pulled the Octogon Boat Table # 315-DSI-KF from our inventory to measure for your specific question. There is a depth of 2-1/4 inches from the top of the cup holder to the very bottom. If you notice in the pictures, there is a ring at the bottom. From the top of the cup holder to the start of the ring, there is a depth of 1-3/4 inches. At the bottom the ring reduces the 3-1/2 inch diameter of the top section of the cup holder to 2-3/4 inches in diameter.
The table diameter,... view full answer...
Hello James. The Replacement Table Leg for Jif Marine Boat Tables - 26" - Stainless Steel # 315-DTX is really the only replacement table leg we sell here. Is has a 2" diameter and is designed to be a replacement leg for the following Jif Marine Boat Table models:
- 315-DSH-KF
- 315-DSH-KS
- 315-DSI-KF
- 315-DSI-KS
Unfortunately, we do not offer anything with a 2-1/2" diameter. Generally, replacement table legs are brand and model specific so if you are able to find that information it... view full answer...
The flush mount version of the Rectangular Boat Table # 315-DSH-KS that you referenced is actually part # 315-DSH-KF on our site so that's what you'll want to order instead.
Attached is a review video for you to check out. view full answer...
The JIF Marine Rectangular Boat Table # 315-DSH-KS that you referenced is going to work perfectly for your application. The black mounting base, once bolted to the floor, is the only component that will be permanently installed when setting up the table. The vertical support tube simply pops into the base and then pops into the circular cutout on the bottom of the table.
When it's time to break down the table you will simply pull up on the tube to remove it from the base (and then pull... view full answer...
According to Jif Marine, when selecting hardware for installation of the # 315-DSI-KS you need to choose a fastener based on the type of material that the table will be mounted to. They recommend a machine fastener like a 1/4 X 20 stainless steel bolt and nut with washers. The thickness of the material would determine the bolt length. view full answer...
The Taylor Made Low-Profile Boat Guide Wheel # 3691214 laying flat is going to be 6" tall. The diameter of the wheel is 14"(see image). These can be stacked to achieve your desired height. view full answer...
The Tow-Rax folding table # TWSP45HFTA is made of aluminum and has aluminum hardware which is not likely to start rusting so salt water would not be a problem. But I would still rinse it off with fresh water when possible to ensure the longest life. view full answer...
The replacement hub that you will want for your 2004 Four Winns boat trailer is part # AKIHUB-655-6-EZ-K. This is a 6,000-lb hub with the same bearings, grease seal and 6 on 5-1/2 inch bolt pattern as your current hubs.
This hub comes with everything you need to install the hub except the bearing grease. If you would like to pick up extra bearing grease, I recommend our marine grease, # L54FR. These are 3 cartridges 3 ounces each, which you can use with or without a mini grease gun.... view full answer...
Yes, the B measurement of the slipper spring part # SP-178275 that you referenced is the correct hanger spacing to use. This puts the spring right where it needs to be on the rear hanger. view full answer...
I spoke with my contact at Lubrimatic and found that they are compatible. The Lubrimatic marine grease is a calcium sulfonate base that is compatible with the lithium complex grease you are currently using. We actually have an FAQ article that covers this very subject. In the article there is a handy table that lists the compatibility of various grease formulations. I have included a link to the FAQ for you. view full answer...
The Fulton Fold-Away Coupler Hinge Kit # FHDPB230101 will work perfectly for your LoadRite 16 foot boat trailer as long as the tongue measures 2 x 3 inches and the trailer tongue thickness is between 1.88 and .120 inches.
It has a weight capacity of 5,000 lbs so it will be more than strong enough for your boat weight capacity of 1,200 lbs (keep in mind that this will not raise your boat trailer capacity). According to the table that is included with the instructions for a 2 x 3 inch and... view full answer...
I went out in the warehouse and pulled the Redline Grease Seal, part # 13194. It does have the markings on the inside of the seal that say TCM 13194 TM Taiwan and the number 11. It also has the spring around the inside lip. This seal will work for your boat trailer application. view full answer...