Timbren Rear Suspension Enhancement System
Item # TFREXPA
Retail:$316.90
Our Price: $269.36
You Save: $47.54
Confirmed to Fit
1998 Ford Expedition
2 Wheel Drive Models
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (6094)
- Q & A (0)
- Photos
1998 Ford Expedition - Timbren Rear Suspension Enhancement System
- Jounce-Style Springs
- Rear Axle Suspension Enhancement
- Timbren
- Standard Duty
3,000-lb Capacity. These hollow rubber springs sit above the rear axle to help stabilize and level your Ford Expedition. They also provide a more comfortable ride by absorbing road shock and improving roll stability. Easy to install and use.
Features:
- Improves suspension, handling and safety
- Provides additional support as needed so you always have a smooth, comfortable ride
- Allows the leaf spring ample movement while cushioning light loads
- Becomes more rigid as more weight is added
- Increases stability - providing great performance while hauling heavy loads
- Reduces vehicle sag
- Works independently - side-to-side
- Helps compensate for off-center loads
- Reduces body roll when swerving and turning corners
- Acts as shock absorbers, taking the brunt of bumps and rough roads
- Extends the life of your vehicle's suspension
Specs:
- Includes 2 Aeon hollow rubber springs, vehicle-specific brackets and hardware for simple installation
- Replaces axle bump stops on frame
- No drilling required
- Capacity: 3,000 lbs
- Do not exceed the vehicle's weight-carrying capacity
- Designed to work with a suspension system that is in good working order
- Limited lifetime warranty - satisfaction guarantee
Whether you're hauling heavy loads in your bed or cargo area or you're towing a trailer, you will often see the rear of your vehicle sag while the front end rises. In these cases, the rear axle is handling not only the weight of the cargo, but also more of the vehicle's weight. Because less weight is on the front axle, the front tires are making less contact with the road. Overall handling - traction, steering, and braking - is negatively affected. But the resistance from Timbren's Suspension Enhancement System works with your factory suspension to keep your vehicle level and improve your driving experience.
The Timbren system comes with custom-fit brackets that are bolted onto each frame rail above the rear axle. Hollow rubber springs are bolted to the bottom of the bracket and hang down to where the bottom of the spring sits, 1" above the axle. The inch of clearance allows the existing factory suspension to operate normally under light loads and standard terrain, ensuring the smooth, comfortable ride that you are used to.
Timbren Suspension Enhancement Systems are designed to work progressively. When the hollow rubber springs are compressed, the convoluted design causes them to quickly collapse along the folds. Once the folds are compacted, the stacked barrel shape increases resistance, stiffening the suspension and keeping your vehicle level.
Each hollow rubber spring works independently to support the driver's side or passenger's side of your vehicle. This is helpful when you swerve or make sharp turns. Each spring is activated when it is needed, so body roll is greatly reduced. The independent action also works well when you are hauling off-center loads.
Because the vehicle handles better with the springs, less turbulence will be passed along to the trailer, and this helps to keep the trailer in line. Your driving comfort is further enhanced if the trailer does begin to sway (from a gust of wind or a passing semi), because the movement from the trailer is not transferred to your vehicle. This also works to make the sway subside more quickly.
Another great feature of the rubber construction is that the springs absorb most of the road shock, creating a smoother, more stable ride overall. Wear and tear on the factory suspension is also lessened because the rubber springs work to prevent bottoming out on rough roads.
Timbren Suspension Enhancement Compared to the Competition
Timbren's Suspension Enhancement Systems are much easier to install than air springs - there are no air hoses to run, no compressors or gauges to hook up, and no manual adjustments to make. The rubber construction makes Timbren's springs more elastic than similar products constructed of microcellular urethane. And more elasticity allows for a more comfortable ride because the rubber has more travel.
FREXPA - Rear Suspension Enhancement System with Aeon Hollow Rubber Springs by Timbren
Installation Details
Customer Reviews
Timbren Rear Suspension Enhancement System - TFREXPA
Average Customer Rating: 4.7 out of 5 stars (6090 Customer Reviews)
3,000-lb Capacity. These hollow rubber springs sit above the rear axle to help stabilize and level your vehicle. They also provide a more comfortable ride by absorbing road shock and improving roll stability. Easy to install and use.by: Daniel05/23/2022
Lincoln Navigator
I’ve struggled with crushing my airbags and having the pump for the airbags burn up trying to keep up and hold the trailer. Using these have absolutely made all of the difference in no longer looks like Sanford and son and the trailer/vehicle stays level. I pull a 36 foot travel trailer weighs almost 8000 pounds with a Lincoln navigator. Absolutely the best thing I’ve installed to support trailer towing.
by: Lorca10/15/2021
2001 FordExpedition
Installed this on my 2001 Explorer. Install is easy (assemble unit, bolt on in place of existing bump stop). Annoyed to find it doesn't fit. Specs are gap 1/2"-1-1/2"; there was a gap of 2-3/4". Yeah, they sell spacers for $27 each, but it's really annoying to buy a $225 product that says it fits your truck, only to find that you have to spend 50% more to actually adapt it to your truck!
by: Mike07/23/2016
1997 FordExpedition
Definitely worked as advertised, very easy to install.
by: John 11/27/2021
by: Sergio 03/06/2021
by: John Z04/19/2023
I know it will be lovely when loaded or the trailer on. However,it rides like a wagon empty with brand new premium shocks and struts empty. Thud thud thud. You really cannot feel the shocks or suspension. Found exact same item plentiful for 60 bucks on eBay after I bought these for 250. I may cut these in half or put air bag on. I do not like the ride empty. No hard feelings. It is a good product maybe just not for me.
by: Paul06/21/2023
Took about 45 minutes to install. But that was 2 trips into the house cause my deep drive sockets were buried. F-350 gasser with 8’ box, Fiberglas cap, 200lb wooden storage drawers and estimated 400lbs in tools. I tow a 14k bumper pull dump that squats the truck. I installed the spacer with the timbrens and it sits on the original axle stop. Ride quality is unknown as I haven’t driven it yet.
by: Hawkeye06/03/2023
Installation was a breeze, removed old bump stops installed Timbrens in about 30 minutes. Haven’t put a load on them yet so I’ll update later. Installed on a 2008 Silverado 2500HD..
by: Shaughn10/21/2022
About a 1/2 inch difference in gap at the bump stop perch but still within parameters. Truck sits perfect with trailer attached. Haven’t towed yet. After towing if they perform like they should will upgrade to a 5 star. Easy to install, definitely needed 2x4 and jack. 2011 Silverado ext cab with 30 ft Genisis 5th wheel.
by: Michael03/12/2023
Was able to install these with a 15mm flex head ratchet wrench and lifted the rear of the truck to make it easier. 30 minutes to take off 4 nuts and put em back on. 2 minutes assembling the timbrens with the added spacer. I have a f350 with a salter and plow. Loaded with salt the lights shoot up and in the snow ?? it’s like hitting hyper drive and you’re blinded. These helped big time. Very happy so far.
by: Tim03/17/2023
The pro: The longer, heavier bump stops worked great when hauling my mustang home from Chicago. The truck stayed level and handled great.
The con: I had to remove the bump stops for everyday use. They limited my suspension travel causing a stiffer ride.
by: OmarG03/08/2023
I am so glad I bought these for my truck. I was able to install them myself using a jack and jackstands. The ride is bit rougher now; but the suspension is totally awesome compared to before. I am able to haul a bit more weight when needed.
by: Paul10/20/2022
Haven’t had it on long, but so far so good. 1999 F350 dually. Bolted up nicely. Total job took 10 minutes. Have hauled two gooseneck loads of hay and truck drives SO much better. Nice and level. Money well spent so far.
by: Francis02/20/2023
very good product ,received just in time and fit perfectly on my GMC savana 2000 .Be sure to clean the two receptacle thats help.
très bon produit , reçu dans les délais et s'ajuste parfaitement . Assurez-vous de nettoyer le receptacle cela facilite l'installation.
by: wirth31505/08/2024
The Timbren SES (Bump Stop) replacement for the 3rd Gen Sequoia is a simple and effetive solution to reduce vehicle sag when trailering heavy loads. You definately want to use the included spacer as the pics will show I still had 2 finger clearance above the axle to allow for OEM suspension travel. I pulled my 29ft boat back to back with / without the Timbren bump stops for a ride quality test. Without the bump stops, my 2024 Sequoia rear end was crushed, resulting in a rough ride and poor handling characteristics. With the Timbern bump stops, the rear sag was reduced signifincantly, and the vehicle drove much better. YES, you will feel and occasional bottom out feeling on abrupt G-out dips... But it is no worse than without the Timberns as the stock springs were crushed. My daily drive feels exactly the same as I have the perfect gap between the Timbren bump stop and the axle allowing the OEM suspension to float over road surface without engaging the bump stops. VERDICT: Time will tell with varied passenger loads, speeds, road surface bumps etc., but my initial impression is 7 out of 10. Ultimately, I would prefer air bags, and may install them along with the Timbrens whih I can swap back to the oem bump stop in less than 15 minutes. NOTE: I was able to install the Timbren bump stops without going under the Sequoia. I simply raised the vehicle frame aprox. 4" withoug picking up the rear tire. This gave me adequate room to reach in over the tire and remove the 3 12MM bolts holding the OEM bump stop in place with a 3/8" ratchet and a 4" extension. Then, I put the Timbren bump stop in place and lightly threaded the upper bolt to hold in place. After installing the two lower bolts and smart torquing, then you tighten the top bolt. This allows the bracket to seat against the frame fully as the top bolt hole is slotted to allow movement druing install. Pics will show spacers installed above the bump stops, Installed bump stops unloaded with 2 finger gap, spacers loaded with 750 lbs of tongue weight, and lastly, will show Sequoia stance while loaded. NOTE: The last picture will show my Sequoia loaded WITHOUT the Timbren SES (Bump Stops) and the vehicle is sagging heavily.
by: Jeffery08/03/2022
The timbrens actually did what they were suppose to do. However, once I starter driving out west I notice the timbrens were riding on the axle which cause the speedometer to jump around depending on the road. I would recommend them if you are hauling or towing a camper or RV. I was going to contact etrailer about maybe removing a spacer for one set however the other set came as one unit. The bottom line is the Timbrens does stabilize your load for safe travels. I will be contacting etrailer soon to assist in correcting the problem...Road trip from Idaho,Colorado,Wyoming,and Utah were beautiful... Thank you etrailer
by: Derrick05/13/2024
Installation was easy and straightforward. Haven’t towed with them yet, but the unloaded ride has not at all been negatively affected. In fact unless you hit a big bump you shouldn’t know they are there but they seem to improve handling around turns when there is a shift to either side in the back. It a HD truck so there is some expectation it’s gonna ride like a covered wagon at times. I added these in conjunction with new Billstein shocks and I’m hopeful all that aggravating bouncing or porpoising my fifth wheel does on bad roads and bridge transitions will significantly improve. etrailer was fast with shipping and follow up. I’ll update after towing.
by: Raymond04/04/2024
Definitely a must have when towing..stiff without a load but night and day difference while towing my travel trailer, better traction, steering and braking. Easy quick install..only issue I had was with the long bolts they sent with the spacer kit (optional for lift) the bolt diameter was too wide to fit through the holes on the bracket..but a trip to the local hardware store took care of that.
by: Jesse03/20/2024
Pros: Cheaper and easier to install than airbags, do the job when load is enough to compress the shock, with added weight or towing, then it stiffens the rear very nicely.
Cons: Doesn't do anything until there is 2-3cm of compressed shock. It sits above the contact point, doesn't touch. Under normal driving, there is no benefit/improved stiffness/anti sway in rear or a leveling of the factory rear sag in a 2022 or newer Toyota Tundra.
If had it to do over, would have put some kind of spacer in between product and upper included bracket, the supplied bolt is long enough to accommodate, to eliminate the gap, and lift the rear 1-2 cm. Should do it anyway, maybe when swapping to summer wheels next month.
by: Rick S06/23/2023
Haven’t hauled my 5th wheel yet so will have to update once i have.
Package arrived promptly, installed in my garage in about 40 minutes with absolute minimal swearing. Installation would have been quicker if I hadn’t wasted time figuring out that my brand new Ford F250 has metric nuts. Great fit, great follow up from the company. I’ll be doing more business with them.
by: Little Doc11/29/2022
I’d seen similar products rated in the 4,000 lb ratings but I went with these. I’m not a mechanic but I removed the factory bump stops and installed both these in 30 minutes or less. I used my rolling jack and lifted from the drop hitch and easily removed the old ones and soapy water and 1/4 twist and these were on. Placed a block of wood in the space between these coils and lowered the jacks then pressed it with my tractor to confirm full engagement. I carry a lot of tools on a 2020 Chevy 2500 I do feel a bit of butt bounce on large bumps but other than that I’m very pleased.
by: Phil 04/18/2023
The order with Will at etrailer was great. He was very helpful and knowledgeable, Installation was not easy but not too bad, The hardest part was removing the factory pieces I removed them from below which was a blind nut removal operation. This is on a 2017 Mercedes Sprinter motorhome. After removal of the factory pieces I discovered that access is much easier on top between the tire and the mud flap, I turned the front wheels inward and they didn't have to be removed. The front of the motorhome had to be raised quite a bit to get the Timbren piece jnserted. Also I learned to tighten the bolt and nut in the Timbren bumper as much as possible before installation because there is no access to the bolt head when tightening the top nut to keep the bolt from turning, preventing tightening the nut.
by: Mark05/09/2024
First off the product was beat up with paint/power coating missing in several places on both. I was putting on a brand new truck with less than 800 miles on it so I elected to touch up before install. I’ve hear a lot about Timbren but never had them. I had airbags on my F350 but when I switched to a new Tundra I went with Timbrens. I’m a bit disappointed in the ride. Feels like I can feel a “bump” in the truck from the rubber pick hitting the axle when I go on a bumpy road. Thinking I should have went with airbags. As far as having a load on the truck and helping with the squat, they do as they are advertised.
by: Allen 06/12/2023
Converted a E-150 to a camper van and the sag was almost 2 inches in the back compared to the front. Installed and now only out 3/4 inch. Van is level and now I can also use my trailer without fear of the van bottoming out. Easy to install. Awesome product!
by: Russell05/31/2024
Product arrived 2 days earlier than expected but due to lack of care for packing metal items one of the metal brackets has chipped paint as per photo. Some of the pieces appear to be previously used.
25
3505
Show More Reviews
See what our Experts say about this Timbren Vehicle Suspension
- Timbren SES For A 2002 Lincoln Navigator With Rear Air SuspensionHey Ronan, Yes, the Timbren Rear Suspension Enhancement System # TFREXPA is compatible with your 2002 Lincoln Navigator's rear air suspension.
view full answer... - Helper Springs or Weight Distribution for a 1999 Ford Expedition that Sags with Boat Trailer CoupledYou have some squat there but I've seen worse! Basically, there are two reasons that a vehicle can squat in the back. One is caused by the tongue weight of the trailer and the other is when you are carrying a heavy load in the back of the vehicle. When squat is caused by a heavy load carried in the vehicle that is when you would use suspension enhancement like helper springs of some kind. But when squat is caused by the tongue weight of a trailer the best solution is to use weight distribution....
view full answer...
- Timbren Rear Axle Suspension Kit for 1999 Ford Expedition Eddie Bauer EditionTimbren rear-axle suspension kit # TFREXPA is a confirmed fit on the 1999 Ford Expedition, both the 2WD and 4WD versions, and it is indeed compatible with the OEM air suspension package in your Eddie Bauer edition. The installation instructions, which I have linked for you, indicate that the Timbren spring replaces your factory bump stop on each end of the rear axle. This is positioned to the outside of the rear coil spring on both sides of the vehicle as shown in the diagram that is included...
view full answer... - Suspension Enhancement System for 1998 Lincoln NavigatorThe suspension enhancement system we have for the 1998 Lincoln Navigator is the Timbren Rear Suspension Enhancement System # TFREXPA. This is a jounce-style system that replaces the axle bump stops and has a weight capacity of 3,000 pounds. Timbren Suspension Enhancement Systems are designed to work progressively. When the hollow rubber springs are compressed as weight is added, the convoluted design causes them to quickly collapse along the folds. Once the folds are compacted, the stacked...
view full answer... - What is the Height of a Timbren Rear Suspension Enhancement System for a 2000 Lincoln Navigator 4x4I went to our warehouse to pull the Timbren suspension enhancement system # TFREXPA to provide you the measurement you are needing. The kit will include 2 rubber springs and 2 vehicle specific brackets for your 2000 Lincoln Navigator 4x4. The height is 3-3/4 inches. See the diagram I included plus the video I created for you. I added a helpful article that you can look at too.
view full answer...
- Recommended Solution to Fight Sag on 2001 Ford Expedition with Timbren Springs Already InstalledWhile the Timbren suspension enhancement for your 2001 Ford Expedition does help fight sag, it looks like a typical Coachmen 252RBS has a GVWR of 7000-lbs or more; any time your trailer weighs more than 1/2 the curb weight of the vehicle, a weight distribution hitch is a good way to help ensure that the trailer's tongue weight is distributed more equally across the axles of the tow vehicle. From what it sounds like based off the weights you mentioned, the weight of the trailer isn't being...
view full answer... - Troubleshooting a 2000 Lincoln Navigator 4x4 with a Sagging Back EndThanks for sending us a picture! Your 2000 Lincoln Navigator 4x4 is certainly lower, and I am thinking you may have the wrong size shocks. Check the length of your new shocks and compare to your old shocks. Most likely your new shocks are too short and will need to be corrected before installing the Timbren suspension enhancement system # TFREXPA. You may need to adjust the ride height to obtain the correct clearance by changing or altering the rubber spring bracket. Or re-arching the...
view full answer...
- Expedition Suspension Enhancement. I wish we had something but oddly enough we don't have any suspension enhancement kits that fit the rear axle of your 2007 Ford Expedition.
view full answer...
Do you have a question about this Vehicle Suspension?
Info for this part was:
Video Edited:
Jacob T
Video Edited:
Chris R
Expert Research:
Adam R
Updated by:
Mary K
Updated by:
Wilson B
Updated by:
Michael B
Updated by:
Carrie F
Updated by:
Bethann B
Video by:
Jonathan Y
Installed by:
Robert C
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Jenny N.
10/19/2021
I will have our customer service team reach out to you. Only if the vehicle is lifted should this kit require spacers. This kit also comes with a 60 day money back guarantee.