To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your Nissan Rogue with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your Nissan Rogue's wiring harness, which is located behind the driver's-side and passenger's-side tail lights. You will have to remove the tail light assemblies and some interior paneling to access this harness. Once you've plugged in the T-connector, run the hot lead up to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery. Once installation in complete, the 4-way connector will be stowed in an out-of-the-way location within your trunk.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. This converter is a circuit-protected, battery-powered unit that bypasses the electrical routes that are used by a basic wiring harness. As a result, there is virtually no draw on your tail light circuits.
Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your Nissan Rogue's three-wire system need to be combined so they are compatible with the wiring system of the trailer. This converter combines the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your Nissan Rogue operate.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
Average Customer Rating: 4.4 out of 5 stars (111 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.This is my second Nissan Rogue install. The first was a 2011, for which I already had a power cable for an amplifier that I wasn't using any more. I really prefer an inside install vs running everything outside. On this 2023 Rogue I jacked up the left front, removed the wheel, then popped all the plugs holding the fender, plus a couple of screws on the little mud flaps. I used the hole for the hood release cable to get the power cable inside. It is well protected by the fender so I'm not worried about water ingress. It feeds in behind the far left of the dash behind the fuses and was easy to pull through. I then ran it along both door foot step trim pieces and through the corner of the back seat into the spare tire area. For the light wiring I used the grommet on each side where the tail light harness passes through the body. I used heavy waterproof electrical tape to re-wrap each grommet to seal out water. The green wire with the passenger side connectors was plenty long enough keeping the control box inside by the spare tire. My last step was to insert the fuse in the red battery connector after everything was connected and buttoned up. Attached my trailer lights and everything was perfect!
I needed to make a trip across country in a hurry but replaced my pickup truck with a Nissan Rogue (w/o a trailer hitch). Working with etrailer we found the right hitch for my vehicle, I purchased it and had my repair shop install it all (hitch and wiring harness). the installation was accomplished easily (feedback from my shop) and I loaded down my trailer and towed it across country with ZERO issues. The etrailer folks really know their QUALITY products. If you are considering adding a hitch to your vehicle, please look them up, you cannot go wrong.
Thank you etrailer, you folks were a real lifesaver.
The trailer hitch went in with no problem. The light kit did need the added wire to reach the passenger side. You would think Curt would have corrected that. Thank you for your service.
This trailer wiring is a great help, but like most others the green wire for the right side is way too short. I knew this going in so I expected it. Still the manufacturer should correct it. I wired mine from the inside to keep it neat and tidy. More work, but worth it to me.
I know I can give you a five star rating from previous experiences and videos supplied from your site. A few paint scratches from shipping but that is to be expected with such a heavy odd shape. A small gloss black paint stick will take care for that. A very easy installation. Should I thank Nissan or Etrailer for that.
Package may have been opened previously as it was taped shut. Had to splice about 2 feet more to get the wiring to reach the right tail light. Installation of the wiring took a little bit longer than the hitch install. Once installed, the wiring worked perfectly.
Connector harness worked perfectly. The green wire for the passenger side is about 24 inches short and had to splice in a piece. Not difficult to do.
Very satisfied with each hitch/light kit I have purchased from etrailer.
The wire to the right taillight is too short. There is absolutely no way for it to reach. Luckily there is extra wire from the wire that runs to the battery for the splice. Other than this the installation was fairly easy with the pictures on line. The papers that come with the harness have black and white photos that are too dark to make out.
Brooke M.
7/18/2023
Regarding the instructions, I wonder if you would fine the pdf easier to read. Its located at the end of all the product information. Regarding the length of the wires, I asked the manufacturer, and you arent the only one having this issue based on other reviews. The manufacturer said to be sure to route the wire on top of the bumper beam. If you go under the bumper beam, it can use up a lot more wire length and cause it to be too short.
Green wire to short on wiring harness …easy fix. Fished in most of wiring, just a few tywraps, no clips needed…
It was so good for my 2023 rouge that i ordered the same thing for my 2024 rouge.
Arrived 2 days early. This came shipped in several layers of plastic wrap along with the light kit, cap and small bracket. It was delivered with no damage or scratches. It was fairly easy to install with the help of my son and a floor jack. we'll do the light kit installation another day. Everything lined up perfectly. We did remove the to plastic pins to make it easier to flex the plastic bumper. trim out of the way. I would recommend it.
This harness works great. Plugs are perfect and instructions fair. The green wire that goes to the passenger side tail light is too short and must be spliced. Seems crazy you have to do this but there's no way around it. It's a fairly involved project but better than risking cutting a modern wiring system. Route the power wire through the cabin to the fuse box. Trying to peirce the fire wall and access the battery is way too much work and likely will damage something.
Absolutely the best place to order from! The video's were very helpful! Thanks everyone from Etrailer you did a great job yet again!
Looked everywhere for a 4 pin wire harness for my 2021 Nissan Rouge. Perfect fit, easy install took less than an hour fit to finish. Photos shows T-connectors separated and connected. Power was an easy run to the battery and ground was simply to chassis. I pulled the 4pin tail to the receiver… done! … First time installing any type of trailer wiring harness.
This kit worked fine for my 2023 rogue sv. However. The wire running between the driver and passenger side taillights is too short and needs extended. This is also an issue with the uhaul kit. Just seems counterintuitive to have to extend a wire on a vehicle specific kit.
Kit is as per what we see in the video. Shipping was fast even to Canada.
Very good customer relations and fast service.
Thank you Carl Cole
Delivered day early & fit perfectly & easy to install
Wiring harness was easy to install.
Watched YouTube to get initial overview.
You guys have known about the green wire being to short for 2 years I am not finished with this by a long shot
Great Price and Super Fast Shipping!!
It would be really helpful if you had a video actually showing the installation on a Nissan Rogue. Also, many people have complained that the green wire is not long enough to reach the car battery under the hood. This has been a complaint for years, so why is this not rectified? Or why is it not able to be wired in the back like other wiring kits?
Sierra K.
7/20/2022
I agree, a video would be helpful. As for the green wire, the manufacturer wants you to route the wire exactly as the instructions say to without deviation so it should be the perfect length per the instructions.
The cable harness did not install as it was stated "It will fit" your vehicle. The right turn signal did not work, also the green lead wire was about 3 feet too short to connect to right tail lamp. The lamp connector lead wires were too short.
All in all a poor execution.
Sierra K.
9/8/2021
I apologize for the trouble you are having installing. This is a confirmed fit for your vehicle from the manufacturer. You do have to install exactly as it says, taking the simplest route, so that all wires fit.
Happy repeat customer
Products fit well and are well made will buy again when needed
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Craig
4/10/2024
Absolutely perfect so far! I always check all my lights before I go with the trailer and it’s been great!