Trailer Wiring Mounting Box for a 2004 Jeep Grand Cherokee and Curt Trailer Hitch 13051
Question:
I purchased the curt trailer hitch 13051. I am looking for a connector that I can mount to this hitch.
asked by: Dave S
Expert Reply:
If your 2004 Jeep Grand Cherokee has a 4-way flat trailer connector then for a mounting brackets there are a few options. You could start with # 18144 to hold the 4-Way and then attach it to either short bracket # 18140 or long bracket # 18136 which attaches to the hitch.
If you need to mount a 7-Way I recommend bracket # PK12711U again with short bracket # 18140 or long bracket # C57202.
If you need to add a wiring harness there are several options depending on how your Jeep is equipped from the factory. If your Jeep did not come with a factory tow package then to add a 4-Way use # C55369.
Products Referenced in This Question
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 4 Round
- 5 Round
- 6 Round
- Tow Ready
more information >
No-Drill Mount for Electrical Mounting Bracket - Short
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 4 Flat
- 5 Flat
- 4 Round
- 5 Round
- Tow Ready
more information >
6 and 7-Way Trailer Connector Mounting Box for Round or Square Tube Hitches
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 6 Round
- 7 Round
- Draw-Tite
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Curt No-Drill Bracket for 6-Way or 7-Way Round Trailer Connector Mounting Bracket - Long
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 6 Round
- 7 Round
- CURT
more information >
Mounting Bracket and Installation Hardware - Pollak 7-Pole, RV-Style Trailer Connector - Vehicle End
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 7 Round
- Pollak
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 600 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: How To Install The Curt T-Connector Wiring Harness In A 2002 Jeep Grand Cherokee
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Installing an Aftermarket Hitch on a 2004 Jeep Grand Cherokee for Jeep Recall
- Q&A: Torque Rating for Spindle Nut on Trailer Hubs
- Article: RV Sway Control, Stabilization, and Suspension Enhancement
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Replacement Brake Assemblies for Dexter 023-358-00 Trailer Brakes
- Q&A: Dual Propane LP Tank Setup 100 Lb for RV or Travel Trailer
- Q&A: What is a Concealed Cross Tube Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Choose the Right Trailer Hitch Class
- Article: Which Hitches are Made in the USA
- Article: 5 Things to Know About Weight Distribution Hitches
- Article: Roadmaster Vehicle Specific Base Plates