Is Thread Locker Necessary on Bolts When Installing a Trailer Hitch
Question:
Hi, I will be installing this hitch on my Pathfinder, soon, and I have a concern about the the attachment bolts, not having a nut to unify them. I was thinking of using thread lock gel of some strength to secure them. Your thought would be appreciated. I certainly will torque them properly, but still a little nervous. Thanks
asked by: Jack
Helpful Expert Reply:
The Curt Class III trailer hitch for your Pathfinder, part # C13126 would utilize nuts that are welded up into the frame member. The conical toothed washers used in the installation do a good job of maintaining the torque applied to the bolt during installation, so threadlocker like # LT37420 isn't necessary although using it won't cause any harm.
If you decide to use threadlocker, and you decide at some point in the future to remove the hitch you'll want to remember to apply heat to the bolts before attempting to loosen them otherwise you could break off the nuts welded into the frame making removal more difficult.
I've linked you to an install video showing the hitch you'd looked at being installed on a 2015 Pathfinder.
Products Referenced in This Question
Loctite Threadlocker 262 - High Strength - Up to 3/4" Nuts/Bolts - 0.20-Fl-Oz Tube
- Lubricants Sealants Adhesives
- Sealant
- Nut and Bolt Sealant
- 0.2 oz
- Loctite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 600 lbs TW
- 4000 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 600 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2020 Subaru Outback Wagon
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: Best Looking Hitch for 2024 Toyota RAV4 Hybrid
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: Curt Trailer Hitch Installation - 2023 Toyota RAV4
- Video: Trailer Hitch Installation - 2014 GMC Acadia - Draw-Tite
- Video: Tekonsha T-One Vehicle Wiring Harness Installation - 2020 Subaru Outback Wagon
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Connector
- Shop: Suspension Enhancement
- Search Results: torque wrench
- Search Results: dog bone
- Shop: Loctite Blue Stick Threadlocker - Medium Strength - 1/4" to 3/4" Nut/Bolt - 0.32 Oz Stick
- Video: Curt Custom Fit Vehicle Wiring - Trailer Hitch Wiring - C56245 Review
- Video: etrailer Class III Trailer Hitch Installation - 2022 Toyota RAV4
- Video: Curt Trailer Hitch Installation - 2023 Toyota RAV4 C66KR
- Q&A: Troubleshooting No Power At The Factory Trailer Plug
- Q&A: Troubleshooting No Power On Curt 4-Way Wiring Harness
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Shop: Brake Controller
- Search Results: 90885
- Search Results: all944001
- Shop: Transmission Cooler
- Shop: Tailgate
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Towing Mirrors