Troubleshooting No Power On Curt 4-Way Wiring Harness
Question:
Had the Curt 2 plug connector hooked up and working well, now it’s getting no power to the plug…the red fuse has been changed and car fuses are good. Has the in line controller gone bad?
asked by: Keith
Expert Reply:
In order to narrow this down I would start by checking the vehicle side of the connector. Check and see if there is power using a circuit tester like the # PTW2993. If you find that there is power then you can rule out anything on the vehicle side and you need to be checking the # C56332
.
If you don't have power then it is a problem with the vehicle. Since you already checked your fuses it is probably a short in the wiring. If you are unable to locate it you will probably have to take it to a local shop for repair.
If the problem is on the Curt wiring harness then use the same circuit tester to see if it has power on the vehicle side of the plug. If it does not, it is probably a short in the wire which you will need to locate and repair.
If everything checks out going into the convertor box check the wires coming out. If you don't have any output then it is safe to say it is the box and you will need a new wiring harness.
I have attached a helpful article on troubleshooting 4-way wiring for your reference.
Products Referenced in This Question
Product Page this Question was Asked From
Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Search Results: bx1758
- Shop: Trailer Hitch
- Shop: Vehicle Tow Bar Wiring
- Shop: Base Plate for Tow Bar
- Shop: Blue Ox Tail Light Wiring Kit - Bulb and Socket
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Tonneau Cover
- Article: Troubleshooting 4 and 5-Way Wiring Installations
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)
- Video: Blue Ox Tail Light Wiring Kit Installation - 1999 Jeep Grand Cherokee
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Search Results: curt 58910
- Search Results: 58910
- Shop: BAKFlip F1 Hard Tonneau Cover - Folding - Aluminum and Fiberglass
- Q&A: Troubleshooting A Turn Signal That Stays On Once The Curt T-Connector Wiring Harness Is Installed
- Search Results: bx8869 bulb and socket wiring kit
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: Curt Custom Fit Vehicle Wiring - Trailer Hitch Wiring - C56245 Review
- Q&A: Are REV And BAK Tonneau Cover Rails Interchangeable?
- Shop: Curt 4-Way Flat Trailer Connector with Circuit Protected Powered Tail Light Converter
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Trailer Hitch Installation - 2014 GMC Acadia - Draw-Tite
- Q&A: What do the Codes for the Test Lamps Mean on CURT Adapter 4 Pole to 7 Pole and 4 Pole # C57674
- Video: Curt Custom Fit Vehicle Wiring - Trailer Hitch Wiring - C55307 Review
- Video: Trailer Hitch Installation - 2001 Toyota RAV4 - Curt
- Video: Trailer Wiring Harness Installation - 2002 Toyota RAV4
- Video: etrailer Trailer Hitch Installation - 2013 GMC Acadia
- Search Results: wiring harness
- Search Results: 13 inch 5 lug
Phil
5/30/2024
I have the Curt wiring harness for my Mazda CX 5. I have all lights working except the marker lights. Any idea what the issue may be.