Dimensions of the Mounting Brackets for Ultra-Fab Trailer Hitch # UF35-946403

Question

Question:

Hi, I need help determining the dimensions of the UF35-946403 hitch mounting tabs.

asked by: Jason R

0

Expert Reply:

On Ultra-Fab trailer hitch # UF35-946403 the brackets that make contact with the frame are 2-5/8 inches by 3-15/16 inches.

expert reply by: Michael H

0

Answer 1

The manufacturer made the Ultra-Fab 2" Trailer Hitch Receiver for 5th Wheel Trailer Frames #UF35-946403 for a weld on application. It is possible to attach the hitch in the manner you suggested, but it is not rated for a bolt on application.…

view full answer...

Answer 2

The Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames #UF35-946403 is an adjustable hitch that will fit inside 2002 Nash 19I with I-beam frame as long as you have clearance at the rear when inserted on the inside of your I-beam. It is…

view full answer...

Answer 3

I attached a picture that shows the distance from the front of the crosstube of the Ultra Fab hitch #UF35-946403 to the front of the hitch opening. That distance is 5-1/4 inches. Depending on where you install the hitch is where the hitch opening…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

The Torflex Lift Kit #K71-707-02 may be exactly what you need for your Winnebago Micro Minnie 1706FB with tandem torsion axles but we do not have any database of axles and I was unable to find the specific axles on your trailer in my research. This…

view full answer...

Answer 9

The Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames #UF35-946403 is a weld on trailer hitch receiver compatible with frames 47-1/8" to 77". It is compatible with I-beam, C-channel, or rectangular trailer frames. The receiver…

view full answer...

Answer 10

Hi Tad, Based on the dimensions you provided I recommend going with the Adjustable Width Trailer Hitch Receiver for RVs, 18" to 51" Wide #C13702. This would mount under the frame with the receiver tube sitting roughly 2" below the…

view full answer...

Answer 11

The puck feet on the Gen-Y Hitch Gooseneck Trailer Hitch for Dodge Ram OEM Puck Systems #GY83XR is just to help stabilize the ball mount and does not lock into place in the puck. The locking mechanism on top will lock the shank into the gooseneck…

view full answer...

Answer 12

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Dimensions of the Mounting Brackets for Ultra-Fab Trailer Hitch # UF35-946403

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching