Correct Wiring Harness For 2008 Ford Escape Limited With Backup Sensors
Question:
2008 Ford Escape Limited 3.0 Part # 118251 I have backup sensors on my escape, it did not come with a trailer hitch. I do have all the relays and fuses under the hood. When i unpluged the backup sensor harness which has 10 pins, only 6 are used for the backup sensors i checked to see if the other pins work and they do, i have power, turnsignals and ground. I just wanted to make sure this part 118251 will plug directly into the factory backup sensor harness and work for towingit seems like it will. If so great, but how come no one makes a adapter harness so both can work at the same time. Obivously you would turn off the sensors when backing up with a trailer so you dont here the beeping noise. It seems like there is no shared pins for each system.
asked by: Gary
Expert Reply:
The item you selected Tow Package Wiring Harness, part # 118251, will not work on vehicles equipped with backup sensors.
You would need to use the T-One Vehicle Wiring Harness, part # 118551, which draws power for your trailer lighting directly from your vehicle battery instead of the electrical system. You will need to plug part # 118551 directly into the vehicle wiring behind each tail light and then run the included wire and make a connection to the battery via included in-line fuse. This harness can plug into your vehicle harness and still allow you to use your backup sensors.
For a trailer hitch for your 2008 Ford Escape, I would recommend etrailer Class III 2 Inch Hitch, part # e56AR.
To complete your towing setup you will need a draw bar, hitch ball, pin and clip.
For a draw bar, I would recommend Curt Ball Mount, part # C45010, which can be used as a 3/4 rise or 2 inch drop. You will need to measure your vehicle and trailer to determine how much of a rise or drop you need (see FAQ).
For a hitch ball depending on the size or trailer coupler you will need 1-7/8 Inch Hitch Ball, part # 19260, or 2 Inch Hitch Ball, part # 19247.
For a Pin and Clip, you will need Pin and Clip, part # PC3, for added security you could use Trailer Hitch Receiver Lock, part # e98880.
I have linked instructions for the T-One Vehicle Wiring Harness, part # 118551.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- etrailer
more information >
etrailer Trailer Hitch Receiver Lock for 2" Hitches - Flush - 2-5/8" Span - Chrome
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Chrome
- Fits 2 Inch Hitch
- Flush Pin
- 2-5/8 Inch Span
- etrailer
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Tow Package Wiring Harness with 4 Pole Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Truck Tailgate Lock
- Shop: Replacement Top Cover Plate for Pace Edwards SwitchBlade Hard Tonneau Cover
- Shop: Bluetooth Control Kit for Pace Edwards Electric Tonneau Covers
- Shop: Pop & Lock Custom Tailgate Lock - Power - Black
- Shop: Trailer Wiring
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Trailer Hitch
- Shop: 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End
- Video: Choosing the Right Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Video: Tow Ready 4-Pole Mounting Bracket Installation
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: hitch
- Search Results: trailer brake controller
- Video: Choosing the Right Brake Controller
- Q&A: Difference Between Curt and etrailer Trailer Hitch Receivers for 2020 Chevy Colorado
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Suspension Enhancement
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Brake Controller
- Search Results: brake controller
- Q&A: What Is An OEM Prep Package And How Do I Know If I Have It
- Search Results: etbc7
- Article: My Trailer Hitch Doesn't Fit