Thank you for the information!
To carry a snowboard and ski carrier we need to start with the roof rack with crossbars and for that I recommend the Malone AirFlow2 # MPG216 which clamps around the raised rails on your 2019 Infiniti QX80.
Now that we have a roof rack we can install our carrier. I really like the Kuat Grip Ski and Snowboard Carrier # GRR6B you were looking at because it's a larger carrier that can hold more than the average carrier, plus it comes with the slide out feature... view full answer...
I have a great solution for you. Even though we do not have pictures of bags/luggage inside the Thule Motion XT # TH629506, we do have the interior dimension to give you the definite measurements that you would be working with. The interior dimensions if the Thule Motion XT 16 are 84-1/2" long x 33" wide x 11-1/4" tall. With these measurements, I recommend measuring the cargo you wish to transport to make sure it would fit.
In order to mount this cargo box on your vehicle, you will need... view full answer...
It sounds like either your Prodigy P3 # 90195 wiring needs to be looked at, or the wiring for the trailer brake circuit.
Start off by checking that the wiring for the P3 is operating as it should. The pigtail connected to the back of the controller will have the following wires connected to the following functions:
Blue - 7-Way Output to Trailer
Black - 12V Power
White - Ground
Red - COLD Side of Stop Light Switch (only gets hot when brake pedal is pressed)
If all of that checks out... view full answer...
The inside dimension of the Curt # C18151 cargo carrier is 57-1/2 inches long by 19-13/16 inches wide by 5-5/8 inches deep.
To determine if you'll have enough clearance to fold the carrier, you'll want to measure from the hitch pin hole in your hitch receiver tube rearward until you clear the rear bumper. I'll link to an article that shows how to do that. This is the minimum amount of clearance you'll need
In order to fold to the storage position, the # C18151 cargo carrier needs at... view full answer...
All weight distribution systems are going to create quite a bit of noise unfortunately. The amount of tension in the setups and the fact there is a lot of metal to metal friction in all of them under all the tension will create quite a bit of noise.
The Equal-I-Zer systems like the part # EQ37100ET you referenced are somewhat noisy but you can quiet them down with the correct lube part # EQ91-00-4250 which helps to keep the noise down quite a bit. This kit would be the much better choice... view full answer...
The # KU24FR three bike version of the Küat Transfer V2 has a weight capacity of 40 lbs per bike. As you mentioned, the 2 bike version, part # KU84FR has a 60 lb per bike capacity.
The Transfer is an excellent bike rack. The U-shaped frame is my favorite feature, it allows you to stand much closer to the rear of the vehicle when loading the inner-most bike onto the rack, which makes it much easier on your back. The rack includes a cable lock for securing the bikes to the rack.
If you... view full answer...
All of the towing mirrors to fit your 2017 Infiniti QX80 are universal since there aren't any custom mirrors available. My favorite universal style is the K-Source # KS3990 because of the dual lens. It allows you to make additional adjustments to see a wider area you.
I've linked a video demonstrating the mirrors on a QX60 for you. view full answer...
Yes, we do offer tire chains for a 2019 Infiniti QX80 with 275/50-22 tires. The Konig Premium Self-Tensioning Snow Tire Chains part # KON24FR are what I recommend. They install only on top the tire so you won't have any clearance issues. They are also easy to setup and come with a nice case to store them in. view full answer...
The Firestone Coil-Rite Air Helper Springs - Rear Axle # F4164 is compatible with all models of the 2016 infinity QX80. The Air Lift Load Controller Compressor System for Air Helper Springs- Heavy Duty - Single Path # AL25854 is also my recommendation for adjustability at your fingertips. view full answer...
I do have some great brake controller options for a 2018 Infiniti QX80 but there aren't any pre-drilled holes or slots in the dash on this vehicle for this purpose. If you don't want to drill into the dash then I recommend the Curt Echo Wireless Trailer Brake Controller part # C51180 which simply mounts outside the vehicle and is then controlled with a mobile device. It does not require any splicing or drilling into the dash therefore there will be no modifications needed.
It works with... view full answer...
The Yakima EXO Swing Away Enclosed Cargo Carrier # Y62VR comes with lock for the pod and one to lock the pod to the frame. It has an anti-rattle hitch pin. You can purchase the Yakima HitchLock # Y07235 to lock the hitch pin, this will secure the entire unit to your vehicle. I have included video reviews of these products for you to check out. view full answer...
I called my contact at Hopkins and they said there should be a wiring connector located behind the rear bumper that a trailer connector can be attached to. I have attached a photo you can check out that may help you be able to identify the connector you would look for.
The trailer connector we offer is part # HM40975. This comes with a bracket to attach the connector on your vehicle. When installed this will give you a working 7-way and a working 4-way trailer connector.
You can use... view full answer...
Each roof rack for your 2017 Infiniti QX80 will have its own specific crossbar spread that works best with your QX80. The range of crossbar spreads from the roof racks that we carry are from 45" to 47" from the middle of the front to the middle of the back crossbar.
If you don't already have a roof rack on your QX80 I highly recommend going with the Thule WingBar Evo system. This option consists of the 60" WingBar Evo Crossbars, part # TH711500 for Silver or part # TH711520 for Black,... view full answer...
The holes around the edge of the # H01465 Let's Go Aero BigBoss cargo carrier are 3/8 of an inch in diameter, so the S-hooks of some ratchet straps would fit. The sides of the carrier are pretty sturdy, but I could see how the carrier box could be deformed if the ratchets were ran down too aggressively. I'd say that the holes are more meant for bungee cords or a cargo net such as what's included with the # H01496 Cover/Cargo net. I'll link you to a product demonstration video featuring... view full answer...
I am happy to confirm for you that yes, the Curt Echo Wireless Trailer Brake Controller # C51180 will absolutely work on your 2019 Infiniti QX80.
The Echo is a really good choice because not only does it give you really smooth braking, but it is also the easiest brake controller on the market to use and install. It is controlled with an app on your smartphone, a device that you're already comfortable using so there is not going to be any unfamiliar hardware or poorly-written manual to... view full answer...
We have what you're looking for.
Blue Ox TrackPro Weight Distribution w/ Sway Control - 7-Hole Shank - 8K GTW, 800 lbs TW # BLU47FR.
This unit will give you the best of both worlds. It will handle your weight distribution issues and provide nice anti-sway capabilities. view full answer...
We don't carry the Andersen No Sway Hitch but we have heard more than a few times that it doesn't do well on higher tongue weights like what you have. The best option would be the Reese Strait Line part # RP66084 that you referenced as it has a tongue weight of 600-1,200 lbs and features best sway control at preventing sway before it starts. view full answer...
Typically a 2017 Infiniti QX80 will use a 60" long crossbar like the # TH711500. The Wingbar Evo can be used with the Evo Raised Rail Feet # TH710401, which will attach to the raised side rails of newer Infiniti QX80's. 60" long bars would likely be the longest bars that you can safely use, as the next longest size available are 79" long, so your best bet is likely going to be those 60" Aero bars. You generally want your crossbars not extend no more than 6" outside of the side rails, and... view full answer...
We carry roof rack tents like the Yakima SkyRise # Y07437 which as long as they are installed on a roof rack with a 165 lb capacity have a tent capacity of 600 lbs. The Malone Roof Rack part # MPG216 has a capacity of 165 lbs so it should work well for you. view full answer...
The Inno Roof Rack consisting of the # INXB123-2 48 inch crossbars and the # INXS100 flush roof rack feet would be a fine choice for your 2020 Infiniti QX80, and is a confirmed fit per Inno.
The Inno Aero Crossbars measure 3-1/8 inch wide by 1-1/8 inch tall and the Rhino-Rack # RMCB is compatible with crossbars up to 3-1/2 inches in width and 1-1/2 inches tall, so they'll work just find together.
I've linked to a demonstration video showing the features of the Inno Aero flush roof rack. view full answer...
Go To Results