For your 2010 Mustang V6, you will need the Draw-Tite Trailer Hitch, part # 24840. The hitch will bolt up to the frame of your Mustang, but since you have a Boss rear bumper, additional trimming of the bumper fascia may be required.
The Draw-Tite Hitch # 24840 is a Class I 1-1/4 inch hitch. You will want to make sure not to exceed the towing and tongue weight capacity of the hitch or vehicle as stated in the vehicle owners manual. If you will be using the hitch for hitch mounted accessories... view full answer...
The only size of trailer hitch receiver for a 2018 Ford Mustang is a Class I hitch with a 1-1/4 inch receiver, the Draw-Tite Trailer Hitch Receiver # 24928.
This is likely because these cars aren't made for towing and don't have the support needed for a larger hitch, so the 1-1/4 inch is all that is available.
Keep in mind that since this is a Class I hitch, your accessories all need to be Class I compatible as well, including a bike rack. So if your current rack is not Class I compatible... view full answer...
There is a cargo carrier that you can use with your 2002 Ford Mustang V6 that has a rise in the shank to combat low ground clearance, though a cargo carrier for a 2 inch hitch won't work for your Mustang. The reason for that is the only hitches that fit your '02 Mustang are Class I, 1-1/4 inch hitches, so you will need a Class I cargo carrier for your Mustang, which we do have.
So for the hitch and cargo carrier, here is exactly what you will need for your 2002 Ford Mustang:
- Curt Trailer... view full answer...
Yes, there should be a washer of some type between the spindle nut and the bearing on your trailer. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut.
There are several types of spindle washers available depending on the spindle configuration on your trailer.
The Washer For 1 inch Spindle, # SW1000, is typically used on spindles that have a castle nut, like # 165686, and a cotter pin, # 165649.
A D washer, # 5-23, would be... view full answer...
In a situation like this there are a lot of variables, like bike rack, bikes, tow dolly, car on dolly, etc, so there is no easy way to figure this out. It is going to take a bit of measuring and basically mocking the situation to see if a set-up will work for you while cornering.
Let's start with the tow vehicle. Using the Curt Multipurpose Ball Mount, # D210, and for this example I am going to use our Kuat Beta Bike Rack, # B202-2, the furthest bike is going to be approximately 30-1/2... view full answer...
You can do this by moving the axles from being above the leaf springs to below the leaf springs.
The diameter of your trailer axle will determine the size of the parts that you will need to order. If your axle is 3 inches diameter, the Dexter Trailer Springs Over-Under Conversion Kit, # K71-385-00, would be a great choice and if your axle is 2-3/8 inch diameter you could use the Over-Under Kit, # K71-384-00. These kits can be installed without welding but the manufacturer strongly recommends... view full answer...
While we don't have a version of the # MF35228 in black you could pretty easily paint this black if you used a high heat black spray paint. Unlike exhaust components closer to the engine the tail pipes don't get hot enough to prevent paint from sticking around. If you paint headers for example the paint will not last as the metal just gets too hot. Exhaust tips are far enough away that the heat not as bad and a high heat paint will do really well. view full answer...
First, if you go through our fit guide for a specific year, make, and model vehicle, if you do not also select a specific trim level (if available) from the drop down menu it will show you all the hitches for all the trim levels. Some fit multiple trim levels so that is why you see it fitting GT and not GT.
You can install a Curt trailer hitch # C11312 on your 2007 Ford Mustang GT as long as it is not a specialty GT model. The easiest way to tell, it fits the Mustangs with the V6, but... view full answer...
In your situation the SeaSucker Monkey Bars Roof Rack part # 298-SX6000B will give you 48" round bars that you can attach the etrailer J-Style Kayak Carrier part # e98878 which has everything you'll need to safely get your kayak to your favorite spots. As there are zero other options this is the way to go.
I've included video on these for you to check out. view full answer...
To replace your Dexter 8-249 hubs, I recommend using the Easy Grease Trailer Hub and Drum Assembly # AKHD-550-35-EZ-K. This is the Axle-Tek brand equivalent of your Dexter 8-249 hub/drum. The hub will include your bearings, seals, races, grease cap and lug nuts. view full answer...
You can get a complete replacement hardware kit for any of the trailer hitches we sell including Draw-Tite trailer hitch # 24687. You will need # RHK. On the RHK page you will see a spot to enter the hitch number and choose the manufacturer. Click the add to cart button and our warehouse team will assemble the correct kit for that hitch. The individual hardware components are not available separately. You would have to get the complete kit. view full answer...
Yes, the MagnaFlow Race Series Axle-Back Exhaust System # MF19345 is a confirmed fit for your 2018 Mustang with the 2.3L I4 Ecoboost Engine. This system has 2-1/2" diameter tubes with a 4-1/2" diameter dual exit and is made from stainless steel. The muffler-less system provides an aggressive tone that is perfect for racing. view full answer...
Definitely don't want to damage your Stang.
The most popular trunk mount bike rack to fit your 2013 Mustang Convertible is the Saris Bones # SA805BL. It'll hold two bikes up to 35 pounds a piece. It's very easy to use and also designed to fit with spoilers.
Since it's a trunk mount, and will be in constant contact with the Mustang, there's always a concern of damage. I don't recommend a trunk rack for long trips or for every day use. But they're a great, economical solution to use... view full answer...
The Rampage Headlight Conversion kit # RA5081126 is the correct size light. 5-3/4 inch round is what your 1969 Mustang had from the factory. This is just the housing, you can grab the H4 bulb at any automotive store around town and just use the original bezel that's holding the current light in place. You can use any off-road H4 bulb up to 130 watts as long as you have the correct amount of power feeding the unit. Standard H4 bulbs will need 55 watts for low beam and 65 for the high beam.
Be... view full answer...
The only base plates I show listed for a 1998 Mustang are the Roadmaster XL Base Plates, # 466-1, that you have referenced. These base plates will not fit an SVT or Cobra model.
Since you have a Blue Ox Rangefinder II tow bar, you would need an adapter to go from Roadmaster Base Plates to the Blue Ox tow bar. The correct adapter is the Blue Ox Rangefinder II to Roadmaster Bracket Adapter, # RM-037.
You will also want to check the owners manual for the Mustang to determine if it can be... view full answer...
For trailer wiring that has been confirmed as a fit for your 2015 Ford Mustang we have the Curt kit part # C56088 which will install easily. I attached an install video as well. view full answer...
Yes, the Draw-Tite part # C11041 will fit only fit1998 Ford Mustangs with 6 cylinders. Since the Cobra models have 8 cylinders, we cannot use it on you 1998 Mustang Cobra.
If you plan on carrying bikes, you could use a trunk mounted bike rack like the Thule OutWay # Th45JV. I attached a video of the OutWay for you to check out. view full answer...
For a hitch for your 2013 Ford Mustang you would want the Draw Tite hitch part # 24863. To install this hitch on your vehicle you would not need to modify the rear fascia/body of your vehicle.
I attached an install video for this hitch for you to check out as well.
This hitch would work great with the Swagman XTC2 Bike Rack part # S64670 that you are interested in. My Dad has this bike rack and uses it on his 2005 Mustang GT convertible and he really likes it. view full answer...
For your 2012 Ford Mustang, The Covercraft Ultra'tect Custom-Fit Outdoor Vehicle Cover - Gray, # C17124UG is a confirmed fit. It will be a really good cover for your needs. The WeatherMax SL fabric is designed to prevent rain, snow, dirt, dust, bird droppings and tree sap from reaching your mustang. This will be a really nice cover for your car as it sits near 2 sycamore trees most of the week, and is easy to remove and store for the days you get out for a drive. I highly recommend... view full answer...
Go To Results