Yes! If you have Yakima JetStream Crossbars installed on your 2002 Audi A4 Sedan with a bare roof, the Thule Pulse M # TH614 can clamp onto the crossbars with no problems. This is because the height and width of the JetStream crossbars are the exact same as the Thule WingBar Evo Crossbars.
If you need a complete roof rack, you need the following components:
- Yakima JetStream Crossbars - Black - 50" Long # Y00425
- BaseLine Towers for Yakima Crossbars - Naked Roofs # Y28TR
- 2 sets... view full answer...
We do offer a 1-1/4-inch light-duty Class I hitch for the 2017 Audi A4 Allroad. My technical contact at Curt confirmed that their Class I hitch # C11448 is a fit and will work well.
If you are planning on towing I recommend a ball mount like part # C45019. This ball mount has a 5/8 inch rise or 1-1/4 inch drop and measures 9-3/4 inches long. For a hitch pin and clip you can use part # F-4.
For a 1-7/8 inch hitch ball I recommend part # C40001 and for a 2-inch ball I recommend part # C40018.... view full answer...
We don't have wire color info for your 2009 Audi A4, but to install the Curt Wiring Harness # 56201 all you would need is a circuit tester like part # PTW2993 so that you can test the function of each of the wires so that you can wire it up correctly to your vehicle.
With this harness you would also want the battery wiring kit part # 55151 to power the unit. view full answer...
Camco Power Defender voltage protectors, parts # CAM55301 and # CAM55306, have a bit more protection than the circuit analyzers, parts # CAM55310, # CAM55312, and # CAM55313.
Both the analyzers and protectors have diagnostic lights for faults but beyond that the analyzers are just surge protectors. The voltage protectors go a little further by detecting the voltage and shutting off if the voltage level falls below 102V or goes over 132V. The voltage protectors also reset themselves... view full answer...
The Curt Hitch part # C11195 that you referenced has been confirmed as a fit for your 2016 Kia Sedona so I would recommend it for your.
If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not include a ball mount with... view full answer...
One of the nicest racks we offer that I recommend is the Thule OutWay 2-Bike Rack, part # TH45JV. This rack differs from most racks because it uses 2 rubber coated straps to secure the carrier to the vehicle versus 6 on most racks.
This carrier uses the OneKey system to lock both the rack and the bikes to deter theft.
If you are planning on carrying bikes with alternative frames like kids bikes or women's bikes I recommend using an adapter bar like part # 64005. This attaches between... view full answer...
Although the exterior body components of the 2005.5 and later model years of the Audi A4 Avant may be similar, or even the same, the frame structures are not. If you compare the mounting flanges for these two hitches, parts # 11164 and # C11180, you will note that the mounting points for hitch # C11180 are vertical (meaning the bolts will be oriented in an up-down direction) while the hardware for hitch # 11164 installs to the spare tire well in a horizontal direction.
Both of these light-duty... view full answer...
What you described is a classic ground issue. The problem is that the added amperage draw of the head/running lights being on for your vehicle makes the trailer taillights a bit weaker.
What you would want to is run the grounds of the light assemblies of your trailer back to the main ground harness of your trailer. I can almost guarantee that will fix the problem.
I attached a help article for you to check out as well that covers 4-way troubleshooting. view full answer...
The shipping weight of the Stealth Hitches Hidden Rack Receiver - Custom Fit - 2" # 391AUDA4A5S509 you were looking at for your 2010 Audi A4 Sedan is 51lbs, and the dimensions of the box will more than likely be 45" x 8" x 25". The reason I say more than likely is that if you order other products with the hitch a larger box may be used to fit all of the products.
I included a link to the written instructions of the # 391AUDA4A5S509 for you to take a look at. view full answer...
Thanks for the information. My recommendation for your roof rack to carry your kayaks is the Rhino-Rack consisting of the following:
-Rhino-Rack Vortex Aero Crossbars - Aluminum - Silver - 46" Long - Qty 2 # RRVA118S-2
-Rhino-Rack 2500 Series Legs for Vortex Aero Crossbars - Naked Roofs or Fixed Mounting Points - Qty 4 # RRRLKVA
-Custom DK Fit Kit for 4 Rhino-Rack 2500 Series Roof Rack Legs - Naked Roof # DK208
This combination will give you the best roof rack at the price-point for... view full answer...
We have a hitch that will fit the Audi A4 Avant Wagon, Including Quattro models. The Curt Class I Trailer Hitch Receiver item # C11195, is the correct hitch for your vehicle. view full answer...
I went out to the warehouse and pulled a set of the load stops # A70770. The inside dimensions that fit around a crossbar are 1.3 inches wide and 1.25 inches tall. view full answer...
The available trailer hitch for the Avant model of the 2010 Audi A4 is Curt Trailer Hitch, # C11195. This hitch comes with the recommended drawbar. The cross tubing will be visible under the bottom bumper. Because of where the attachment points are on the vehicle, the hitch will be visible. I have included a link to the installation instructions below.
With this hitch installed, you will just need a hitch ball and wiring for the trailer. For a ball, you can use # 19256 (1-7/8 inch diameter)... view full answer...
There is fascia trimming required to install the Curt trailer hitch part # C11448 that you referenced.
I attached a picture that shows where the trimming will be needed. view full answer...
Unless you have done some modifications that would put your exhaust in the way of the Draw-Tite Sportframe Trailer Hitch Receiver # DT24950 (see attached photo) you should be good to go.
I have also attached an installation video and the instructions for you to reference.
If you let me know what you will be using it for I can make some recommendations for you. view full answer...
To carry the bike you sent us a picture of with the Thule Passage # TH910XT you would have to use a bike frame adapter bar part # UB01 since it does not have a horizontal top tube. view full answer...
The best 235/80-16 trailer tire we have for you is the Provider Radial Trailer Tire part # PRG80235. This tire has a 14 ply and load range G rating which is good for up to 4,080 lbs (per wheel). It has a maximum speed of 81 mph and comes with a two year warranty. The reason I recommend the Provider is because unlike most other trailer tire manufacturers, they bake test all of their tires which increases longevity.
I have attached a review video for you as well. view full answer...
Yes, fascia trimming is required to install Draw-Tite trailer hitch # DT24950 on a 2016 Audi A4. The area that needs to be trimmed is up underneath the vehicle and not visible otherwise. I have included a diagram that shows the area that needs to be trimmed. This is a bottom view as if you were lying on the ground looking up at the bottom of the vehicle.
If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated... view full answer...
The Thule Sidearm Wheel-Mount Bike Carrier TH594XT is not compatible with the Thule XADAPT9 Load Bar Adapter for Echelon, Peloton and Prologue Bike Racks # THXADAPT9 because of it's head assembly. This system is limited to certain bike rack models, but the vast majority are not compatible with the t-slots.
If you are interested in a bike rack that is easy to install and has the locking functions, I recommend the Yakima FrontLoader Wheel Mount Bike Carrier # Y02103. I've attached videos... view full answer...
Yes, the trailer hitch that fits your 2008 Audi A4 Quattro sedan is the Curt Class-I # 11164. The maximum tongue weight is 200 pounds.
Note, that all non-trailer loads such as bike racks, cargo carriers and more must be supported by stabilizing straps like # 18050. If not, you will void the hitch warranty from Curt.
I included a installation video on a older Audi A4 and a couple informative articles for you to view. view full answer...
Go To Results