Metal Low Profile Replacement Cover
(503 reviews)
Price: $33.01
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (503)
- Q & A (0)
- Videos (3)
- Photos
Ventline RV Vents and Fans - BV0534-00
- Replacement Lid
- Roof Vent
- 14W x 14L Inch
- Ventline
- Silver
- Metal
Replaces the flat metal cover on Ventline Ventadome RV roof vents.
Features:
- Replaces the flat, low-profile, metal lid on Ventadome roof vents for motor homes and enclosed trailers.
- Works with Ventline Ventadome roof vent model V2110.
- Measures: 14-1/4" by 14-1/4"
- Mill finish
- Made in the USA
BV0534-00 Ventline Metal Low Profile Replacement Cover
Video of Metal Low Profile Replacement Cover
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Ventline Replacement Operator for Trailer Roof Vent Installation
Today on enclosed trailer we'll be installing the Ventline replacement operator with knob and screw for Ventline Ventadome trailer roof vent with metal dome. Part number BV0115-04. We'll also be installing the replacement dome assembly for the Ventline Ventadome trailer roof vent. Part number Bv0534-00. Now you'll need to first take apart the interior portion of the vent. There's four screws that hold the outer trim piece on.
You want to be extra careful here, as the plastic becomes very brittle as it gets older. Next there's two screws, one on the front and back, that hold the screen in place. These are small Phillips head screws. With that done, we'll go ahead and set the screen down out of the way. Next, you'll remove the two screws that hold the operator arm in place. You'll then slide the operator arm out through the slot.
We'll then take the new operator arm, slide it back up into place, and put the two screws back in, holding it to the frame of the vent. Next, we're going to need to go up on the roof of the trailer. Now we're ready to install the new cover. Just slide it in from one side and as you're doing that you want to make sure that the actuator arm slides through the round portion and then up into the channel. Now, it makes it a little easier if you have someone down in the trailer to help guide this through, or to raise and lower the actuator arm if need be. Now, we'll go ahead and lower the lid all the way down where we can bend the tab over. You want to make sure that both sides are bent far enough that there's no chance they can slide back out of the track.
Next, we'll need to go down into the trailer where we'll be attaching the friction clip to the operator arm. That way it can't come off of the new lid. You want to make sure that the concave side of the clip bears against the dome bar. If you've attached the handle temporarily, you will need to unscrew it so we can put the screen back up into place. Once the screen's back up into place you can go ahead and put the handle back on. Finally, we'll put the trim ring of the piece of plastic that goes around the outer edge with the four screws.
With that, that's all there is to it, to replacing the Ventline replacement operator with knob and screw for the Ventline Ventadome trailer roof vent with metal dome. Part number BV0115-04. .
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- Wrong item was ordered
- Arrived Damaged
Customer Reviews
Metal Low Profile Replacement Cover - BV0534-00
Average Customer Rating: 4.9 out of 5 stars (503 Customer Reviews)
Replaces the flat metal cover on Ventline Ventadome RV roof vents.by: Wendy05/30/2023
I waited several months before writing a review so that I could make sure this replacement cover didn't leak. It hasn't! It was really easy to install which I did myself. For reference, I'm a 53 year old woman. Our trailer is an enclosed aluminum trailer, and this cover fit perfectly.
by: Gabe R05/18/2024
Perfect replacement. I have no idea who the original vent manufacturer was. The old opaque plastic cover cracked and broke from age and weather. This fit right in its place, and raises and lowers just like the old one. Hopefully, this one will last longer than the old plastic one. We'll just have to see how long it takes to rust out.
by: Glenn09/14/2023
The cover came very quickly and securely in the mail, very durable, well constructed and stream-lined. Installed fairly easily with your on line installation Tudors. Unfortunately my base has a different type hinge, so a few minor challenges, but for the most part doable. I still need to find a friction clip to secure my top to the actuator mechanism, but hopefully I can find it locally. Our Arizona sun destroys most plastics as our original cover had failed in about five years. I am very pleased with my new cover top, looking to it meeting and exceeding our needs!
by: Jim H06/24/2016
We have replaced over a dozen cracked and UV damaged plastic roof vents on our cargo trailers with the Ventline metal vents and replacement metal covers from etrailer.com.
etrailer has always provided us with fast turnaround time on deliveries and excellent follow-up and their pricing is very competitive.
I recommend etrailer to anyone who needs trailer parts and accessories.
Jim H.
by: Bruce09/23/2016
I am very pleased with your service and received the Roof Vet Covers in a timly manner.
The covers fit just fine and look nice. See trailer picture attached.
by: Leanna09/15/2019
Came exactly as advertised. Installed quickly. No pictures of before, the plastic completely fell apart in removing. I opted to paint it white with Rustoleum, and it works great. Wish I had known this was available the last time we replaced it. Should never have to replace this on this unit again. Will definitely remember this for ANY future applications.
by: Wes H08/22/2018
Ordered this metal vent lid to replace the deteriorating plastic lid on my 2017 Lark trailer and have no regrets. This lid is well built, fit perfectly and operates smoother than the plastic one because it flexes less. Followed the directions on the package and had the lid replaced in 10 minutes or so. It was an easy swap and probly the best investment I could have made for the integrity of my trailer. No more worrying about hail busting that cheap plastic lid. I will definitely be ordering my new trailer with this lid installed. I highly recommend replacing those cheap plastic lids with this one.
by: Rhonda P. 06/01/2019
I ordered 3. I received them promptly, but the hinged area that you slide onto your camper was to loose and the cover came off when I opened it. So I had to use a pliers and crimp them smaller. Then one had rivets on the support bar where the other 2 did not so it won’t close all the way.
by: Gerald 04/26/2024
Good quality vent a lot better than the plastic ones easy to install thanks again
by: Dave in NC10/22/2014
Much lower profile than the original plastic dome I shattered when rolling my trailer into the garage (DOH!).
The Installation video was helpful but, due to the obscure screws my trailer manufacturer used to install the vent, I had to work topside, above the screen, using an offset screwdriver.
The replacement dome arrived very quickly (which was good, 'cause rain was on the way).
by: Murray12/23/2019
Shipped promptly. Easy installation. Seems to be a great lid
Murray
12/25/2020
Its been solid! No leaks,cracks or issues. Very happy with my purchase.
by: K.G.05/10/2019
The plastic vent cover on my 2018 trailer, only a year old started crumbling and disintegrating, received this metal cover from etrailer.com and was very satisfied, shipping was quick and installation was easy, probably the last vent cover I will ever need for this trailer.
Thank you etrailer.com
by: Yolanda09/28/2023
Just perfect.we have been wanting to replace our sky light covers with metal covers for a couple of years
by: Rodrigo01/28/2019
Thanks
El producto tal como se indicaba llegó perfecto y calzó muy bien en mi camper. De muy fácil Instalacion, no más de una hora. Gracias
(The product as indicated was perfect and fit very well in my camper.
Very easy installation, no more than an hour.
Thank you)
by: Frances 01/19/2024
Was Very easy to install! Very Robust and looks great!!
A great alternative to the plastic which only lasts a few years!!
by: Doug L.10/30/2012
Just what the doctor ordered!! Needed to replace the two old cracked plastic vent covers on my 1982 vintage Alaskan camper with more durable lower profile alternatives to better fascilitate the use of the boat/canoe rack and to stand up better to heavy snow
loads. The BV0534-00 worked equally well on both the original DTS
unit and the newer Elixir replacement unit and will undoubtedly hold up to the elements much better.
Doug L.
4/30/2014
Its now been over a year now since I installed the two Ventline BV0534-00 replacement covers on my old Alaskan camper and they are holding up very well and performing as good as new in spite of being continually exposed to the Ozark elements and excessive humidity.I just wish I had installed them years ago and avoided the expense and hassle of having to replace several inferior plastic covers over the years.Quality speaks for itself.
by: Thomas05/05/2023
Looks like it will be a perfect fit, won't have to worry about the plastic rotting out anymore since this one is metal quality looks good, fast shipping thank you
by: James 09/09/2023
Cover was easy to replace and fits well. I either missed the recommendation that the seal may need to be replaced or there should be . Eitherw way I'm happy will be ordering a seal.
by: Jef lindenmayer08/28/2019
I purchased two flat metal vent covers for my 5th wheel as it sets outside in the extreme elements of the Arizona desert. Prior to me finding the metal vent covers at etrailer I would have to replace the plastic vents every year. Glad I found these vent covers. Get a couple for yourself and never worry about having to replace them again.
Jef Lindenmayer
Jef L.
8/29/2020
These vent covers have eliminated the need for annual replacement. Save yourself some time from crawling on top of your RV and keep the money in your pocket. Buy the metal vent covers.
by: Todd04/01/2019
Perfect fit, easy install and most of all this item should not crack after 1 year of use like the plastic models and leak while on the road in a rainstorm. The only drawback is less natural light in the trailer but less light is better than ruined cargo due to water damage. This item should last the life of the trailer.
etrailer.com always gets your item to you promptly with great tracking options.
Todd R.
4/8/2020
One year later and still working perfectly!
by: Thomas02/21/2018
Good vents, fit right and only one desire is that they were aluminum instead of galvanized metal. Eventually will rust so am giving a protective coating to further retard rust. Replaces my old 5th wheel vent covers; second or third time, now
will not have to worry about having to replace again as with the plastic ones.
Esther T.
2/24/2019
GREAT! Only problem was too low for bathroom vent but a little hammer work took care of that. Last one I will have to do.
by: Daniel 06/26/2020
I purchased the metal dome replacement for my ventline trailer roof vent because the original completely crumble to pieces after two years. Like always Etrailer shipped extremely fast, parts were packaged superb, installation was extremely easy and well documented with lots of instructions and the fit and finish was by far better than the originals. etrailer is the best!!
Daniel
6/27/2021
The vent covers are the best I have ever owned! I would recommend them over any other product!
by: Wild duck08/12/2013
eTrailer comes through again with fast, excellent customer service. Quality of the replacement dome is simply excellent, and U.S. made too! The old plastic dome became brittle with sunlight and age and the replacement is simply excellent. eTrailer, you do it right and thanks for such good service..... This metal replacement will outlast me....
Wild D.
2/10/2015
eTrailer replacement parts are the only way to go for me... the metal vent cover is simply great and was so easy to install too. Price was great, service was too, and followup lets us know eTrailer cares about the products and customer.
by: Jerry 05/07/2020
These metal vent covers were purchased to replace plastic covers on motorhome.
Easy to install. Did have to hammer dimple in one to clear vent fan motor in bath.
metal covers are lower profile than plastic. Have not had any condensation on inside of covers which was a problem with plastic in high humidity.
Jerry
5/30/2021
working fine, no problems
25
503
Show More Reviews
See what our Experts say about this Ventline RV Vents and Fans
- How to Pick Out Replacement Vent Cover Recommendation for a 2004 Fleetwood WildernessThere are a few things to look at when looking for the correct replacement vent cover for your trailer. The first item that will help is knowing the manufacturer of the vent on the trailer, such as Elixir, Jensen, Ventline etc. The next thing that you will want to consider is the size of the vent itself. The Vent Cover, # BV0534-00, that you referenced is designed to fit plastic vent frames that are 14 inches by 14 inches. The actual outside to outside dimensions of this vent cover are...
view full answer... - Can Older Ventline Roof Vent Lid be Replaced with Metal LidYou can replace your plastic vent cover # BV0554-01 with the metal lid part # BV0534-00 that you referenced and you'd be set.
view full answer... - Metal Replacement Cover for RV Bathroom Roof VentThe only metal roof vent cover we offer is part # BV0534-00 which is meant to fit on a 14 x 14 inch roof vent with a continuous hinge. If this fits the description of your existing vent, the # BV0534-00 would work well for you.
view full answer... - Replacement Vent Cover for my 1989 Starcraft Fifth WheelThe Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vent part # BV0534-00 is a great choice for replacement covers. They are designed to work with the vents that have the solid full length hinge. If you have a different hinge type the MaxxAir UniMaxx Universal Replacement Lid for RV and Trailer Roof Vent part # MA00-335001 is a replacement meant to work with all types of hinge configurations.
view full answer... - Best Replacement Metal Roof Vent CoverWe offer a replacement metal roof vent cover that fits the standard 14 x 14-inch roof vents that are typically found on RVs. Ventline part # BV0534-00 is a plain metal finish flat lid with a continuous type hinge. This is the only metal lid we offer at this time. I linked a photo showing the hinge since this is an important aspect to its fit on the vent. If your vent uses a different style of hinge (all types appear on the other linked photo) you can refer to the linked page for all types...
view full answer...
- Can a Metal Replacement Vent Cover be Used to Replace a Plastic Vent CoverReplacement vent covers are very specific in terms of what vents they will fit. Metal cover # BV0534-00 is designed to fit Ventline Ventadome roof vent model V2110. If your vent originally had a plastic cover chances are this metal one will not fit. I have included a link to the vent covers we carry. If you are not sure of the model number you will need to look at the hinge style on the existing cover and compare it to the hinges pictured on the product pages of the covers.
view full answer... - How to Select Replacement Lid for Trailer Roof VentReplacement roof vent lids come in one of three hinge types and this you will want to match to yours as you select replacements. Please refer to the linked photo that shows the three hinge types, 3-point, 4-point and continuous. You can then use the linked page for roof vent lids to select the hinge type and preferred color. For example, for a flat metal vent lid with a continuous hinge you can use part # BV0534-00.
view full answer...
- How to Find Which Replacement Vent Lid Replaces Cracked Vent Lid on 1987 Lynx Prowler CamperWhen measuring for a replacement vent lid, you will want the outside dimension of the housing that extends through the trailer roof. This dimension is typically 14 by 14 inches. Closely examine the remaining portion of the vent, looking for a manufacturer name or model number. If you cannot find that information, you can examine the replacement lids we offer (see link) and match them up by the dimension of the housing and the style of hinge. Each replacement lid will have a detailed photo...
view full answer...
- Size of Replacement Vent Cover for Roof Vent on 2008 StarCraft Pop-Up Camper Model 2107The majority of square trailer roof vents are a standard size, about 14 x 14-inches. I found a few photos of your StarCraft camper trailer and it does appear that this is the size on yours. The replacement vent lids we offer come in many colors and in four basic hinge types. You can use any color you want but you need to match the hinge type to ensure a good fit. Please refer to the linked photo that illustrates the various types of hinges used on roof vents. Find your type and then refer...
view full answer...
- Availability of Metal Replacement Trailer Roof Vent Lid We do have one replacement metal dome assembly with the Ventline # BV0534-00, which is the lid that is used on the Ventline Ventadome Roof Vent # V2110SP-24 you referenced. You can use this unit to replace the existing plastic lid on your vent as long as it features a continuous hinge. I have attached an image that zooms in on this portion of the lid so you can make sure.
view full answer... - Recommended Replacement 14" x 14" Continuous Hinge Roof Vent Cover for 40 Year-Old TrailerFrom the picture that you sent in it looks like your vent cover has a continuous hinge. If that is the case then you just need to confirm that it measures 14" x 14". If it does meet those requirements then the Replacement Lid for Elixir RV Roof Vent # CAM40156 will fit! You could also use the metal Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vent # BV0534-00 or the Smoke Replacement Lid for Ventline and Elixir RV Roof Vents # CAM40148 as well depending on what you are...
view full answer...
- Recommended Replacement Lid For A Heng's RV Roof Vent The metal dome # BV0534-00 assembly you were looking at measures 14-1/4 inches by 14-1/4 inches and connects with a continuous hinge. From what I can find on your Heng's vent, it's a 3-point hinge style so this lid would not work. We do carry however have an alternative option with the MaxxAir UniMaxx Universal Replacement Lid for RV and Trailer Roof Vent # MA00-335001. This vent comes with a bolt-on hinge that you can screw into the side of your vent to make the lid fit and operate properly.
view full answer... - Replacement Metal Vent Cover Recommendation for a Ventline Ventadome Trailer Roof Vent # V2110SP-24Yes, there is a replacement cover available for the part # V2110SP-24 that you referenced. For that you would want the part # BV0534-00.
view full answer... - Fit and Compatibility of Ventadome Metal Vent Cover on a Hengs Vent on a Rockwood CamperWe do carry the replacement vent covers for Hengs vents. If you want to just replace the cover you would order part # CAM40153 which is designed to work with the metal base after a redesign. This is the only replacement cover that uses a 3-point hinge that we carrry. The original vent cover measures 14 inches by 14 inches and so do these two covers mentioned above. The metal dome # BV0534-00 assembly you were looking at measures 14-1/4 inches by 14-1/4 inches and connects with a continuous...
view full answer... - Will White Replacement Vent Cover Last Longer Than Smoke Colored Cover For Pre-1995 Elixir Roof VentWe offer one metal replacement vent cover. It is part # BV0534-00 but it is designed for a 14-1/4 x 14-1/4 inch vent. The 61635 and 61634 are designed for a 14 x 14-inch vent. The discontinued part 61635 is made of plastic so I don't think there will be a lot of difference in the length of time either replacement lid will last.
view full answer... - Can a Metal Vent Cover Replace the Plastic Vent Cover for a Ventline Trailer Roof VentYes, the metal replacement dome assembly # BV0534-00 you referenced will work as a replacement for the plastic vent cover # BV0554-01. The replacement cover # BV0534-00 measures 14-1/4 x 14-1/4 inches and is a galvanized metal to combat corrosion. I included a couple videos that you can take a look at too.
view full answer... - How to Pick Out Replacement Vent Cover for 2009 American HaulerIf your roof vent had a plastic cover on it then the correct vent cover would be the part # BV0554-03. If instead you had a flat metal cover you would need the part # BV0534-00. Both of these have continuous hinges.
view full answer... - Does Ventline Metal Roof Vent # BV0534-00 Fit Ventline Roof Vent # V2094SP-28Yes, the metal vent lid cover part # BV0534-00 is designed to fit the Ventadome style of Ventline roof vents like the part # V2094SP-28 you mentioned.
view full answer... - Locating Replacement Roof Vent Lid for Trailer We have a large selection of replacement RV roof vents available. In order to choose a compatible replacement for your trailer/RV, you will want to first measure your existing cover or vent and also take a note of its hinge style. I have attached an image that shows the different styles that we have available. For example, the Ventline Replacement Dome Assembly # BV0534-00 measures 14-1/4 inches x 14-1/4 inches and features a metal continuous hinge. I have included a short video demonstration...
view full answer...
- Ventline Metal Roof Vent Cover for 1970 Pilgrim Truck Camper?14 inches square is the standard roof opening for vents, vents with fans, and air conditioners - so you are on the right track. There are two pieces to the Ventline # BV0534-00: the vent body that is screwed and sealed to the camper roof, and the lid to the vent body. I the vent body was damager beyond mending, then this is the right part for you. If you only need the lid, which is frequently the case, then you need to take a close look at it and determine what style of lid hinge you...
view full answer...
- Can Metal Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vents be PaintedReplacement Dome Assembly # BV0534-00 doesn't have to be painted but you could paint it if you want to. There are special requirements for painting galvanized metal though. The first thing you will need to do is clean the galvanized parts with water-based cleaner/degreaser to remove any of the oily film on the parts from the galvanization process. Once clean you will need to use a water-based primer. Do not use a petroleum-based primer because the oil can interact with the zinc on the...
view full answer... - How Does Trailer Roof Vent with Metal Lid Install on Roof of CamperThe Replacement Dome Assembly # BV0534-00 that you referenced is just a replacement lid for a roof vent. It attaches to the hinge of a roof vent and to the operator arm which raises and lowers it. For the entire assembly that uses this lid you'd want the part # V2110SP-24 which to install it you'd want the kit part # 344270KITW that comes with screws to attach it to your trailer roof and also sealant to make it water proof. I attached an install video for this kit that shows what it comes...
view full answer... - Low Profile Vent Cover for Ventline VentadomeI wasn't able to find out what vent cover you have or its dimensions from the info you gave, or if you needed a cover or replacement lid. There are flat lids such as the # BV0534-00 and low covers such as the Vent Cover for Ventline Old Style Rounded Dome Trailer Roof Vents # BBC0530-01. I have added a link to our page with each of our replacement lids as well as a link to our page with our selection of vent covers for you to take a look at. If you let me know the dimensions of the cover...
view full answer...
- Replacement Roof Vent Lid for Pace American Trailer with 14-1/4" VentsVent lids are actually very universal so since you have the standard vent measurements and a continuous hinge you can definitely use either part # BV0554-01 or part # BV0534-00 depending on which style you like better. I have attached installation videos for both lids that you can check out.
view full answer...
Do you have a question about this RV Vents and Fan?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Robert G
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Video Edited:
Zack K
Video Edited:
Chris R
Written by:
Raymond P
Installed by:
Cole B
Updated by:
Mary K
Updated by:
Manda E
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Leanna
9/16/2020
It’s been installed a year now and still looks and works great. Best replacement for the top vent on the market. I am not sending another pic, because it still looks as good a year later.