7" Weld-On Bracket Kit for Draw-Tite Class V Ultra Frame Service Body Trailer Hitch

See what our Experts say about this Draw-Tite Accessories and Parts

• Trailer Hitch Availability to Fit 2017 Mercedes Sprinter with Service Body
  I spoke to my contacts at Curt and Reese and the only styles of hitches that can be made to fit a service body truck like yours are multi-fit RV hitches like the # 41990 that has a 16k capacity. This is a weld on hitch that would require either the 7 inch drop brackets part # 4907 or the 16 inch brackets part # 4916. The rear ends on service bodies are all different dimensions so there's no way to have a hitch fit that works well with that vehicle configuration.
  view full answer...
• Recommended High Capacity Hitch for Class C RV on 2007 Chevy Express 3500 Cutaway Van Chassis
  For a cutaway van chassis, we typically recommend a weld-on application that's typically used on a service body truck like the Draw-Tite # 41990. You'll also need frame brackets, either # 4907 for a 7 inch drop or part # 4916. To determine how much drop you need, measure downward from the underside of the frame member until you clear the underside of the bumper. The # 41990 is a class V hitch with a 2 inch receiver opening. The hitch has a 16K towing capacity/1600 lb tongue weight capacity,...
  view full answer...
• Heavy Duty Hitch For A 2004 Safari Simba 34SBD Pulling A Trailer
  From what I could find, your 2004 Safari Simba 34SBD will be rated to 4,000 pounds towing. This will be due to the powertrain and capacity of the frame. With that said, you may be able to use the Draw-Tite Ultra Frame Service Body Trailer Hitch Cross Tube # 41990 paired with the 7" Weld-On Bracket Kit # 4907 or 16" Weld-On Bracket Kit # 4916, but you will be limited by the lowest rated component. In this case, that will be your RV.
  view full answer...
• Receiver Hitch For 2014 Newmar Canyon Star Motorhome At Least 6,000 lb. GTW
  The Curt Adjustable Trailer Hitch Receiver, Class III - 2", # C13701 that you link to, has a maximum gross trailer weight rating of 5,000 lbs. However, this is increased to a maximum GTW of 6,000 lbs. when used with weight distribution system. My first suggestion is that prior to changing out current hitch, identify with Newmar if the factory installed hitch has similar rating as this may meet your needs. The two Curt Trailer Hitches, # C13702 and # C13701, are both rated the same with...
  view full answer...
• Travel Trailer Hitch Recommendation for Cargo Carrier for Small ATV
  For what you are looking to do I would recommend a multi-fit hitch like the part # 41990 that has a 16k capacity. This is a weld on hitch that would require either the 7 inch drop brackets part # 4907 or the 16 inch brackets part # 4916. This hitch can work great on frames that are up to 44 inches apart. If your frame is wider than that you would want the part # 13703 that is adjustable for frames that are from 22 to 72 inches in width.
  view full answer...
• Recommended Trailer Hitch For A 1998 Utilimaster Step Van
  The Draw-Tite Ultra Frame Service Body Trailer Hitch Cross Tube # 41990 will definitely be a good option for your 1998 Utilimaster step van, as long as the frame is not longer than about 44" as you will need some cross tube for the brackets to be welded on. As to the brackets, the correct ones will depend on how low the bumper sits from where the hitch will be mounted to the frame. We have these brackets in a 7" drop ( # 4907) as well as a 16" of drop ( # 4916) if needed.
  view full answer...
• Which Hitch Will Fit a 2004 E-350 Cab and Chassis with 14 Foot Box Truck Body
  For a 2004 Ford E-350 Cab and Chassis the Draw-Tite # 41906 is a custom fit, but you will need to make sure that the bolt holes are 38-5/8 inches from frame to frame in order for it to fit your particular model. While this hitch is a custom fit for the E-350 cab and chassis, it's possible that your box truck body may not have that hole spacing on the frame so you will want to confirm this. I've linked an installation video that can be used as a rough guide, since we don't have any videos...
  view full answer...
• Hitch Option For Saf-T-Liner Bus With 41 Inch Frame
  We do, but you'll have to weld a hitch onto your Saf-T-Liner as there is no bolt on or otherwise custom fit option. So for your 41 inch frame width, you'll need the Draw-Tite Ultra Frame Service Body Trailer Hitch Cross Tube # 41990. Then for the brackets, measure from the top of the frame on your bus to the bottom of the bumper. If you need 5-9/16" (or less) to clear the bumper you will use 7" brackets # 4907; if you need 14-3/8" (or less) you will use the 16" brackets # 4916.
  view full answer...
• Trailer Hitch Recommendation for 2007 Chevrolet G35 with Service Body Hitch
  Looks like you have a service body truck/van based on your pictures. There are only multi-fit hitches that will fit that type of vehicle. I spoke to my contacts at Curt and Reese and the only styles of hitches that can be made to fit a service body truck like yours are multi-fit RV hitches like the # 41990 that has a 16k capacity. This is a weld on hitch that would require either the 7 inch drop brackets part # 4907 or the 16 inch brackets part # 4916.
  view full answer...
  
• Trailer Hitch for 2002 Thomas Saf-T-Liner Bus
  There is a way for you to add a trailer hitch to your 2002 Thomas Saf-T-Liner bus although there are none mounted vertically onto the frame, they will use brackets to mount to the frame which can be bolted or welded on. What you need is the Draw-Tite Ultra Frame Service Body Trailer Hitch Cross Tube # 41990 so long as your bus has a frame which is up to 44" wide, because that is the length of this crosstube. You will then use either the 7" Bracket Kit or 16" Bracket Kit. To determine...
  view full answer...
• Recommended Class III Hitch for 2009 Ford E-450 Chassis Bus
  I have a solution for you, but there is not a Class III custom fit hitch available for a 2009 Ford E-450 Bus chassis and the 7" Weld on Bracket Kit # 4907 with the Draw-Tite Ultra Frame Service Body Hitch # 41990 is a Class V hitch- so it's not exactly what you're seeking. Instead, you can use the Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703, which is a Class III hitch that will fit on box frame, I-frame or C-frames between 22" and 72" wide. This hitch can either...
  view full answer...
• Hitch Availability for a Truck with Ambulance Body
  I spoke to my contacts at Curt and Reese and the only styles of hitches that can be made to fit an ambulance body truck like yours are multi-fit hitches like the # 41990 that has a 16k capacity. This is a weld on hitch that would require either the 7 inch drop brackets part # 4907 or the 16 inch brackets part # 4916. I also attached a link to a page that has all of the hitch extenders we carry. You should note that products like this cut the capacity of the hitch in half when used.
  view full answer...
• Recommended Bolt On Hitch for a 2002 Ford E-450 Ambulance
  The best option to add a hitch to your 2002 E-450 Ambulance is going to be the Draw-Tite Ultra Frame Service Body Trailer Hitch item # 41990-07. There are no custom fit hitches availabe. This hitch can be bolted on or welded to your Ford's frame. This hitch fits frames that are up to 44" wide. It is a class V hitch with a 2" receiver, that has a 16,000 lbs towing capacity. I have linked the installation instructions below so you can see the requirements and decide whether or not this...
  view full answer...
• Availability of Class V Trailer Hitch for 1990 Ford E-350 with Ambulance Body
  The best option for a trailer hitch that can install on your 1990 Ford E-350 with an ambulance body is a weld-on hitch like the Draw-Tite Class V # 41990. You will just need to add either the 7 inch drop brackets # 4907 or the 16 inch brackets part # 4916. I do recommend having the installation done by a qualified professional welder. Because of the lower body at the rear of ambulance models there isn't a traditional bolt-on custom hitch available that is confirmed to fit. I have attached...
  view full answer...
• Recommended Hitch for a 2010 GMC Savana Cutaway
  No, it won't but I have a hitch that will. I checked with Buyers Products and the frame's a different width on the newer Savana cutaways so the item # 3371801102 won't work. Since there are no custom fit hitches for a 2010 GMC Savana Cutaway, you will need to use a universal option. I recommend the Draw-Tite Ultra Frame Service Body Trailer Hitch Cross Tube item # 41990 and one of the following mounting brackets: 7" Bolt or Weld-On Bracket Kit item # 4907 16" Bolt or Weld-On Bracket...
  view full answer...
  
• Hitch Recommendation for a Ford Truck with a Rear Lift Gate
  None of the custom fit hitches we carry are going to have a distance of 10 inches or less from the rear mounting hole to the hitch opening. Your best option is going to be a multi-fit hitches like the # 41990 that has a 16k capacity. This is a weld on hitch that would require either the 7 inch drop brackets part # 4907 or the 16 inch brackets part # 4916.
  view full answer...
• What Towing Setup Would Work For My 2012 Mercedes Sprinter
  When installing there is a few parts you would need to start the installation. For the vehicle side you would need to start with part # 118650 which would give you the beginning 4 flat plug. From the 4 flat plug you would need part # ETBC7 which would make the 4 flat into a 7 round, and also giving you the additional wiring needed to activate your trailer brakes. On the trailer side part # HS381-9000 would provide the attachment to plug into the ETBC7. For the brake controller part #...
  view full answer...
• Hitch Recommendation for Custom Fit Application
  If you have a cab and chassis truck with a 34 inch wide trailer frame (measured from outside to outside) then the # C15845 would line up enough to allow you to drill holes and install it. The top of the hitch opening will measure 6 inches from mounting surface of your vehicle. If your vehicle frame isn't 34 inches a better solution would be the multi-fit hitch part # 41990 that has a 16k capacity and either the 7 inch drop brackets part # 4907 or # 4916 for 16 inch drop.
  view full answer...
• Hitch Recommendation for 2008 Ford Super Duty With Utility Bed
  For vehicles with utility beds we aren't going to have a custom fit hitch available but we have a universal fit hitch that would work well. It will require a more in-depth install though. I spoke to my contacts at Curt and Reese and the only styles of hitches that can be made to fit a service body truck like yours are multi-fit RV hitches like the # 41990 that has a 16k capacity. This is a weld on hitch that would require either the 7 inch drop brackets part # 4907 or the 16 inch brackets...
  view full answer...
• Possible High Capacity Hitch fit for 1999 Ford F-550 with Modified Chassis
  I really wish we had a custom fit hitch but the best option would be a multi-fit hitch. I spoke to my contacts at Curt and Reese and the only styles of hitches that can be made to fit an RV like yours are multi-fit RV hitches like the # 41990 that has a 16k capacity. This is a weld on hitch that would require either the 7 inch drop brackets part # 4907 or the 16 inch brackets part # 4916.
  view full answer...
• Trailer Hitch Compatible with Liftgate Truck
  We have many hitch options for a truck that has a lift gate, but very few of them are a simple bolt on custom application. Because the locations for attaching lift gates vary, you will need to use a weld on option like the Class V Universal Weld-on Receiver Hitch # 15903. There are many different bracket options for a hitch like # 4907 and # 4916.
  view full answer...
• High Capacity Trailer Hitch Recommendation for 2005 Class C Jayco RV
  I spoke to my contacts at Curt and Reese and the best option would be the # 41990 that has a 16k capacity. This is a weld on hitch that would require either the 7 inch drop brackets part # 4907 or the 16 inch brackets part # 4916 depending on the dimensions of your setup. You should note that just because the hitch has a 16k capacity that does not mean you can tow 16k. You would need to determine the towing capacity of the RV and go by the lowest rated component. This is a multi-fit...
  view full answer...
• Trailer Hitch and Wiring for a 22 Passenger Bus Built on a 2002 Ford E-450 Van Chassis
  There are no confirmed trailer hitch fits for the E-450 cutaways but I do have a solution that could work for you. You can use a weld-on heavy duty truck hitch # 41990. Then you can use 7 inch brackets # 4907, or 16 inch brackets # 4916. This requires a qualified professional welder for installation. For a wiring harness you could use universal harness # 118344. This is a powered wiring harness meaning it gets the power for the trailer lights form the vehicle battery. This helps protect...
  view full answer...
• Hitch Recommendation for a 1993 Dodge Roadtrek Camper Van
  I spoke to my contacts at Curt and Reese and the only styles of hitches that can be made to fit a camper van like yours are multi-fit hitches like the # 41990 that has a 16k capacity. This is a weld on hitch that would require either the 7 inch drop brackets part # 4907 or the 16 inch brackets part # 4916.
  view full answer...

Do you have a question about this Accessories and Part?