Powered Converter Wiring Kit

See what our Experts say about this CURT Accessories and Parts

• Does the Wire Need to Be Run to Battery of a 2010 Volkswagen CC to Install Trailer Wiring
  Sounds like you are asking if it is necessary to run the power wire of the Curt Wiring Harness part # C56200KIT to the positive side of your battery since the part # 55151 is just the portion of the harness that runs to the battery. You will have to run this wire for the wiring harness to function properly. The reason it is needed is to protect the delicate wiring of your vehicle. The # C59236 uses the taillight circuits of your CC as signal wires only and draws all of the amperage for...
  view full answer...
• Can Trailer Wiring Harness Power Wire be Connected to Outlet at Back of Vehicle Instead of Battery
  Only the battery should be used when installing any type of powered trailer wiring harness. Part of the reason is that it is not tested in any other way. A connection to the battery is reliable but going through some other circuit could lean to unforeseen and unwanted operation of the system. Plus, if the circuit for that power outlet at the back is fused with or otherwise connected to any other circuit then you will lose that level of isolation between the tow vehicle wiring and the trailer...
  view full answer...
• Troubleshooting Installation Of Curt C56496 On A 2023 Chevy Bolt EV
  I did not see any mention of connecting the black wire on the converter. In order for the Curt # C56496 to function properly, you will need to connect the black wire to the battery in order to power the converter. If you do not have the black wire connected this will explain why you are getting low voltage out of the converter. You can use the wiring kit # 55151 to run power to the converter module.
  view full answer...
• Trailer Hitch Availability for 2009 Mini Clubman S
  According to Curt, the receiver hitch you referenced, part # C11387 will fit the 2009 Mini Clubman S. To see installation details, click on the provided link. The ball mount and a pin and clip are included with the hitch, you might also need the following to complete your towing system: Wiring Harness with 4-pole Trailer Connector, part # 119250KIT 1-7/8 Inch Trailer Ball, part # 19256 2 inch Trailer Ball, part # 19258 Locking Hitch Pin, part # e98879 You can see the hitch installation...
  view full answer...
• How the Curt Trailer Hitch Installs on a 2006 Mini Cooper and is Any Trimming or Cutting Needed
  The CURT Trailer Hitch, # 11126, will fit all model Mini Coopers EXCEPT the S series. You will not have to cut or trim any visible part of the bumper. The hitch will fit, more or less, around the stock parts on your 2006 Mini Cooper, but you may need to trim a small portion of the opening at the back of the vehicle for the fascia to fit back on the vehicle correctly once the hitch is installed, see instructions link. There are several specific steps that need to be taken to complete installation,...
  view full answer...
• Trailer Wiring Options for the 2014 Ford Escape
  A couple of wiring harnesses have recently been listed as a fit. For the 2014 Ford Escape without the towing package you can use wiring harness # C56190 or # 118566. If you decide to go with # C56190 you also need installation kit # 55151. Both harnesses will install the same way. You will need to use the included circuit tester to test the vehicle wiring behind the tail lights and tap into them as described in the linked instructions.
  view full answer...
• How to Determine if a Chevy Volt has a 2 or 3 Wire Taillight System
  The easy way to determine if your Volt has a two or a three wire system is to check the taillights. If the turn signal is amber in color, you have a three wire system. If your turn signal and brake lamp on each side of the vehicle use the same bulb, you have a two wire system. So, if your Volt has a two wire system you would ground both the red and the white wires from the converter to the vehicle. I've linked you to our trailer wiring FAQ article
  view full answer...
• Recommended Hitch and 4-Way Wiring for 2022 Mazda CX-5
  It definitely makes more sense to go with the # C56496 and # 55151. The only difference between this combination and the # C59496 (aside from cost) is the addition of a circuit tester. If you want a circuit tester you could add the # PTW2993 and still come out on top. If you haven't decided on a hitch yet, I recommend the etrailer # e98902 for your 2022 Mazda CX-5. My favorite thing about this hitch is the matte black finish. This gives it an OEM look that tends to blend in better on vehicles....
  view full answer...
• Can The Universal 7-Way Kit # ETBC7 Be Installed In A 1973 Ford Bronco
  Hey Jeff, Yes, the Universal Installation Kit for Trailer Brake Controller # ETBC7 can be installed on your 1973 Ford Bronco. You'll will need to have a 4-pole connector first though. If you don't have one then you'll need the Curt 4-Way Flat Trailer Connector with Circuit Protected Powered Tail Light Converter # C56496 along with installation kit # 55151. Once installed you can then install the # ETBC7, but will still need a brake controller. If you haven't picked one out yet then I...
  view full answer...
• Does Curt Trailer Wiring Harness for 2020 Toyota Camry Hybrid Require 55151 Install Harness
  For your 2020 Toyota Camry Hybrid the Curt trailer wiring harness part # C85FV is a confirmed fit. The wiring harness part # 55151 is required to run the power wire up to the battery as well. It is confusing that it shows as "not a fit" for your vehicle but I can assure you it does.
  view full answer...
• Replacement Ring Terminal for Curt Trailer Wiring Harness 2019 Hyundai Tucson
  For a replacement ring terminal that came with the Curt trailer wiring kit part # C89KR that you referenced you'd want the # DW05741-1. For a replacement battery line you'd want the part # 55151.
  view full answer...
• Correct Curt Trailer Wiring Parts for a 2022 Mazda CX-5
  The Curt Upgraded Circuit Protected Powered Tail Light Converter # C56496 along with the Powered Converter Wiring Kit # 55151 are what you need to add wiring to your 2022 Mazda CX-5. Sometimes our fit system needs adjustments made and this is one of those times. You're good to go with these parts! If you're looking for a complete towing setup then I also recommend checking out the etrailer Hitch # e98902 because of the durable matte black powder coat and then the ball mount kit # EBMK4...
  view full answer...
• Wiring A Furrion Camera System To Work While Not Hooked Up To The Tow Vehicle
  Your trailer is only going to have power running to the running light and reverse light circuits (one of which is powering your camera) while hooked up to the truck. To bypass this you can wire the lights to the battery using two diodes # RM-792 (to prevent feedback), an in-line fuse # 55151, a switch # 37212225 to control the power running to the camera as needed, and some wiring. You'll want to splice the power wire from this switch together with the power wire already running to your...
  view full answer...
• Taillight Converter for 2010 Harley Davidson to Tow Trailer with Combined Stop/Turn Signals
  If you need the actual converter to combine the bike's separate stop and turn signals into a combined signal to match your trailer, then you can use Curt 3 Wire to 2 Wire Converter # C56190. This converter takes in separate stop and turn signals and outputs combined signals on the yellow and green (L & R) wires. You will also need Powered Converter Wiring Kit # 55151. If your hog has an existing wiring harness that has a 5-pole flat type vehicle connector and your trailer has a 4-pole...
  view full answer...
• Curt Universal 4-Way Vehicle Wiring Harness For a 2016 Mercedes-Benz CLA-250
  Yes, you can use the Curt 56187 wiring on the 2016 Mercedes-Benz CLA-250. We only carry the upgraded version # C56496 and you will need the Powered Converter Wiring Kit # 55151 with either of the Curt converters.
  view full answer...
• Trailer Wiring Harness for 2009 VW Jetta Sportwagen TDI
  Yes, you are correct that Tow Ready wiring harness # 118667 is intended for only the 4-door sedan versions of the Jetta. For a 2009 VW Jetta Sportwagen TDI Tow Ready does not offer a wiring harness. However, Curt does have 4-pole wiring kit # C59236 that is a confirmed fit for the 2009 Volkswagen Jetta Sportwagen Wagon, including the TDI. I linked an installation video for this item showing a 2009 Sportwagen TDI. You can use install kit # 55151 to simplify the process. This includes...
  view full answer...
• Parts Needed to Connect Battery Bank to Inside Lights on Snowmobile Trailer
  For your application I recommend using an in-line fuse holder like the 10 Amp Kit # 55151 or the 15 Amp Kit # C55152. These some with butt connectors and a lead wire to run for power so you get everything in a kit. A circuit breaker, like the 20 Amp # PK54520, is rated for higher things like a trickle charge from your tow vehicle battery to the trailer battery bank which is why I recommend the fuse instead of the circuit breaker. Aside from the fuse you'll need a switch like the Single...
  view full answer...
• Towing Capacity & Hitch Recommendations For 2006 Mercedes E350 Wagon
  It's critically important when you start out looking to tow things with your vehicle that you use a hitch that is designed to be used with your vehicle and a rig/trailer accessories that are designed to be used with that hitch. Your 2006 Mercedes E350 Wagon is designed to be equipped with Class I hitches only, such as the Curt # C11701 , designed for light-duty towing, has a tongue weight capacity of 250 lbs, and a gross trailer weight capacity of 2500 lbs. There is not a custom wiring...
  view full answer...
• Trailer Hitch and Wiring Recommendation for a 2003 Audi A4 Avant Wagon Towing a VW Bus Conversion
  The Avant version of the 2003 Audi A4 is the wagon version, so the Curt Mfg. trailer hitch, # 11164, will fit on your vehicle. we have a link to the installation instructions that I attached for you to review. The Curt Class I receiver hitch is rated by the manufacturer for towing trailers up to 2,000 lbs maximum, fully loaded and ready to travel, and with a maximum tongue weight of 200 lbs. You will also need trailer wiring. If your trailer has a 4-Way connector the you will use part...
  view full answer...
• Can Trailer Running Lights be Powered Off of a Battery When Not Connected to a Trailer
  I do have a way that you can wire the lights on the trailer so that they will come on when connected to the tow vehicle or off of a battery on the trailer. What you will need to do is add 2 diodes, # RM-792, to the wiring set up. You will also need a switch, # D16740, and a wiring installation kit # 55151. I have included a diagram of how this should all be wired. Basically the wiring to the light will come from 2 sources; the trailer connector, and the battery via a switch. The diode...
  view full answer...
  
• Will the BMW 5 Series Wagon Hitch Fit the BMW 5 Series Sedan
  For the 2008 BMW 5 Series Sedan the only hitch we have available is the Curt Class I Hitch, item # C114983. This is a 1-1/4 inch receiver hitch with 2,000 lbs towing capacity and 200 lbs tongue weight capacity which is the same as the hitch for the wagon that you referred to. The Curt Class I Hitch, item # C11194, hitch is designed for the 2008 BMW 5 Series Wagon and will not fit the Sedan models. At this time our suppliers do not offer a 2 inch receiver hitch for the 2008 BMW 5 Series. If...
  view full answer...
• Recommended Trailer Wiring for 2013 Audi S5 Convertible
  I'm glad to hear that you're happy with the hitch you purchased! Curt hasn't tested a wiring harness on your vehicle, so they couldn't make a recommendation. The correct harness will depend on what kind of wiring system your S5 uses. You'll need to use a circuit tester like part # PTW2993 on the circuits feeding the taillight assemblies. You could have a 3-wire or a Pulse Width Modulation (PWM) system. Regardless of the type, the ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole...
  view full answer...
• Is In-Line Fuse Needed When Installing Wiring Harness on 2010 Volkswagen CC
  Yes, you will want to install an in-line fuse close to the battery when running a power wire directly from the battery to the converter. When installing Wiring Harness on your 2010 Volkswagen CC you will want to use the Curt Powered Converter Wiring Kit, part # 55151, to run the separate wire to the battery. This part will contain 20 feet of 12-gauge wire and an in-line fuse holder with a 10-amp fuse that is used to connect the vehicles battery to the powered converter. I am including...
  view full answer...
• Can I Wire My Curt Wiring Converter Kit Differently On 2010 Jetta Sportwagen
  You will want to wire the powered converter directly to the battery at the front of the vehicle so that there is a constant power source from the battery and not the vehicle's electrical system. The power wire is ran to the battery so that it is not pulling power from the electrical system but directly from the battery. In addition to running the power wire to the battery, you will need to use a circuit tester, part # PTW2993 to find the taillight functions of each wire. You will need...
  view full answer...

Do you have a question about this Accessories and Part?