Superwinch Front Mount Electric Winch Wiring Installation - 2004 Ford F-250- Video
Today on a 2004 Ford F250 we're going to install part number SW2007 for Superwinch. First thing we're going to do; we're going to attach a 30 inch wire from the engine to the vehicle frame. This will assure a good electrical ground. There will be a mount on the engine that were going to use and we will go ahead and attach it to that. We'll pull off the wire harness, put the cable on the stud, and then tighten it down with a new nut. Now the part number we're using for this night is going to be 185917. more
6/12/2013 10:04:45 PM
Yakima Roof Rack Fairing Review - 2013 Ford Edge- Video
Today on this 2013 Ford Edge were going to be test fitting the Yakima Roof Rack Fairing, part number y07048. Our fairing has already been assembled according to the instructions so all we need to do is install on the front crossbar. To install our fairing we use the clips on the back and top side of the fairing to go around our front crossbar. Once we have each clip in place and the fairing centered with our vehicle, were ready to tighten down the clamps on the ends with the included bolt and wing nut. When we have those fastened, our fairing is installed. That completes todays test fit for the Yakima Roof Rack Fairing, part number y07048 on our 2013 Ford Edge.. more
6/7/2013 11:40:50 AM
Trailer Brake Controller Installation - 2002 Ford F350- Video
Today, on our 2002 Ford F350, we're going to be installing Tekonsha Prodigy P2 Trailer Brake Controller, Part Number 90885. In conjunction with the brake controller, we'll also be using the Tekonsha Plug-in Wiring Adapter for electric brake controllers, Part Number 3035-P.To begin with, we will go ahead and lower dash panel below the steering wheel by twisting the four corners of the panel and pulling it off. With this removed, we'll go ahead and locate the plug that we will need to plug into underneath the dash.The connector is a gray connector and we will need to take the end of the plug-in wiring adapter and plug into this. You want to make sure it goes in all the way to where you hear it click and lock into place.Next, we'll go ahead and pick out a location to secure our mounting bracket. On this particular vehicle, there was already a brake controller installed before, but we'll go ahead and change out to the new bracket.We'll go ahead and make the connection to the back of the brake controller. Again, you'll notice that there is a clip on the one side and you need to make sure that it's locked into place firmly on the back of the brake controller.We'll go ahead and use the two screws and put the brake controller up into the bracket. more
5/24/2013 10:45:14 AM
Trailer Brake Controller Installation - 2003 Ford Explorer Sport Trac- Video
Today on this 2003 Ford Explorer Sport Trac were going to install part number 90885 from Tekonsha. To help install our brake controller were going to be using the following parts. Were going to be using the etbc7 kit and also a bracket, part number 18136 from Tow Ready. Now well start off installing our bracket to the hitch because we need this bracket to install the seven-pole bracket that comes with the etbc7 kit. Well go ahead and connect the seven-pole bracket to our mounting bracket, and then well attach it to the hitch. Well wrap up our seven-pole adapter wires with electric tape leaving out the four-pole, the blue wire which is our brake wire and the black wire which is the 12 volt power supply. more
3/28/2013 7:04:10 AM
Tow Ready 4-Pole Mount Bracket Installation - 2013 Ford Edge- Video
Today on our 2013 Ford Edge well be install the Tow Ready Mounting Bracket 4-Pole Flat connectors, part number 18144. With the big car equipped with the 4-pole, stored inside the vehicle, well need to ride it outside and then secure it with the 4-pole mounting bracket also using the Tow Ready No Drill Mounting Bracket, part number 18140. Our first step, well open up the rear cargo area. Then remove the spare tire cover. Now go ahead and remove the threshold and cargo storage box on the drivers side. Now we can access the 4-pole connector and grommet just below the cargo tray. more
3/15/2013 8:04:13 AM
Edge Backup Camera for Color Touch Screen Monitors Installation - 2003 Ford F-250- Video
Today on our 2003 Ford F250 well be installing the Edge Accessories backup camera for Edge color touch screens, part number EP98201. To begin our installation well remove the license plate frame containing the camera from the packaging, and after removing our license plate from our truck, here, well line up the bracket on the bumper where the license plate would bolt up. Youll notice that the camera has a wire that comes out of the frame here on the top. Our truck doesnt have a place where we can pass the wire through, so were going to go ahead and drill a hole. Youll notice that the wire has a rubber grommet on it already, so well use that grommet as a guide for the hole it will drill. We may need to open the hole up a little bit in order to get the grommet in. more
3/7/2013 3:22:47 AM
Trailer Brake Controller Installation - 1991 Ford F-150- Video
Today on our 1991 Ford F150, we will be installing the Tekonsha PowerTrac electric brake controller, part number 39523 in conjunction with the ETBC7 Brake Controller wiring as well as the replacement brake control plug in harness for Tekonsha and Draw-Tite type brake controllers, part number 20127. We will begin our installation here at the rear bumper. We will need to install the bracket to the rear bumper that will hold our 7 pole connector. We will take the bracket and the hardware, put the bracket in place here in the redrilled holes. Slide the bolt through, put the washers on the other side and lock it down with the nut. With both bolts in, we can go ahead and tighten it down securing it to the rear bumper. We are now ready to put the 7 pole into the bracket. We will take our 7 pole connector and the hardware here, put the connector into place making sure that the wires pass through the bracket and with our connector in place, we will pass the bolts through the connector, through the bracket, put the nut on the other side and tighten them down. more
3/6/2013 9:21:42 AM
Trailer Brake Controller Installation - 2004 Ford F-150 3035-P- Video
Today on this 2008 Chevrolet Silverado were going to install part number 39510. This is the Tekonsha Voyager Brake Controller. Couple of things to know about this brake controller; first off, were working with an older version of it. The old version doesnt have the port on the end of the wires. Not to start off well go ahead and look for the two package wires underneath the dash of our truck. Well look up underneath there and we should see a blue wire, a red wire, a white wire, a light blue wire with stripes and an orange wire. more
3/1/2013 4:12:02 PM
Trailer Brake Controller Installation - 2012 Ford F-150 22292- Video
Today on this 2012 Ford F150 were going to install part number 90185, the Prodigy brake controller. Were also going to use part number 22292 from Tekonsha. This is a Tow Ready plug in wiring adapter for electric brake controllers. First off well go ahead and locate the port for our adapter cord. Its underneath the dash right next to the diagnostic board. Well go ahead and cut the tape away from it and pull it loose. more
3/1/2013 10:15:38 AM
Trailer Brake Controller Installation - 2012 Ford Van- Video
Today on our 2012 Ford Van well be installing the ETB C7 brake controller installation kit, part number ETBC7 in conjunction with the Tekonsha P2 brake controller, part number 90885-3034P. The first step of our install will be installing the seven pole bracket onto our new seven pole. Well go ahead and use the hardware provided with our installation kit. Well drop the screws through the seven pole and then secure them with the nuts on the back side and tighten them down. Next we can then go ahead and secure the seven pole bracket directly to the bottom of the bumper using some self-tapping screws. Before I feed the wires over the hitch Im going to go ahead and use some black electrical tape to wrap them up, to help in protecting the wires and cleaning up our installed look. more
2/8/2013 4:02:31 PM
Trailer Brake Controller Installation - 2002 Ford Ranger- Video
12/26/2012 6:39:55 AM
Putco Box Board Running Boards Installation - 2005 Ford F-350- Video
Today on our 2005 Ford F350 Super Duty well be installing the Putco Master Boss rounded running board, box board, part number P62522. Note, on this application well need to trim the rear edge in order for it to fit properly with the dual rear wheel setup on this vehicle. First well go ahead and take a straight edge, mark the line and then cut off the top edge. Now with that done were ready to go ahead and install the front end cap. This will be a black cap secured with two cap screws and a quarter inch flange nut. Then well move to the rear flap, or cap, which will be a large polished sheet of steel that well need to remove the protective film from. more
12/20/2012 2:50:12 PM
Trailer Brake Controller Installation - 2002 Ford Van ETBC7- Video
Today on our 2002 Ford Van well be installing the ETBC7 brake controller seven and four way installation kit part #: #TBC7. First well start at the back of the vehicle. Well mount the bracket for our sever four way plug. To mount the bracket well go ahead and set the bracket up where wed like to mount it and then using a paint marker well mark the holes thatll need to be drilled out. Because of the thickness of the bumper well use a small drill bit as a pilot hole and then step up to our larger size. Now with our holes drilled out well go ahead and take a couple of self-tapping screws and secure the bracket to the bumper. more
12/17/2012 9:05:42 AM
Trailer Brake Controller Installation - 1997 Ford Van- Video
Today on this 1997 Ford Van Club Wagon were going to install part #: 90885 from Tekonsha. Well also use part #: 3035P also from Tekonsha for our adaptor that goes to the factory port thats located in the van. First thing well do is well go ahead and locate the port thats underneath the dash of the van. Itll be located off to the left hand side behind the parking brake. Well plug in our adaptor cord and then well find a location to mount our bracket for our brake controller. Now to locate our brake controller bracket on the left hand side of the dash just blow the headlight switch. more
12/17/2012 1:32:33 AM
Yakima Roof Rack Fairing Review - 2012 Ford Taurus- Video
Today, we're working with the 2012 Ford Taurus and will be test fitting the Yakima 44-inch Fairing for Yakima Roof Racks, part number Y0748. To man our fairing to the roof rack, we'll simply fit all four of the clips over our front cross bar. We do want to make sure that the fairing is centered from left to right, in-between the towers, then we'll come back and use the carriage bolt and wing nuts to secure the outer two clamps on either side. With that done, our fairings installed and we can hit the rood with much less roof rack noise. That's it for our test fit of the Yakima 44-inch Fairing for Yakima Roof Racks, part number Y0748 on the 2012 Ford Taurus. more
11/21/2012 11:47:04 AM
Trailer Brake Controller Installation - 2005 Ford Expedition- Video
Today this 2005 Ford Expedition were going to install part number TK90160 from Tekonsha. This is a primus brake controller. Were also going to use the adapter cord, part number 3635-P, also from Tekonsha. Well go ahead and start off by working with this part. Well plug into a towing port thats underneath the dash. In this case its behind the data port, alongside the wires that goes to it. more
11/6/2012 3:09:00 PM
Bestop PowerBoard Motorized Running Boards Installation - 2003 Ford F-350- Video
Today on our 2003 Ford F350 well be installing the Beststop Powerboard motorized running boards with LED lights, part number B7510415. First well need to attach the motor linkage and idler linkage for our running board. To do this well first take the U nut, insert it into the inner rocker panel of the truck. Starting with the rear motor linkage well then use the new 8 mm bolt and flat washer and thread them into the U nut. Now well go ahead and take the motor linkage and slide it into position with the two bolts that we just installed. Next well take the two socket cap screws and 10 mm washers, thread them through the rocker panel and into the threaded portion of the motor linkage. more
11/1/2012 2:54:42 PM
Optronics Off Road Lights Installation - 2006 Ford F-150- Video
Today in our 2006 Ford F150, we'll be installing the optronics 6-inch round, 100 watt halogen off-road lights. Part number MH100W. We will also be using the Optronics relay wiring kit, part number A-720. Our first step will be mounting the lights. Because the design of our light bulb we'll not be able to use the manufactures lower, rubber or metal washers. We're going to replace that with a 1/2-inch plat washer and then secure it with the manufacturer's split lock washer and nut. more
10/23/2012 7:31:22 AM
Trailer Brake Controller Installation - 2004 Ford Explorer- Video
Today on this 2004 Ford Explorer we're going to install part number ETBC7 We're going to use this to install Brake Controller part number 90885 from Tekonsha, the Prodigy P2 Brake Control. So we'll start off our install by installing a mounting bracket onto the hitch. Now this bracket does not come with the kit and we'll be using part number 18140. Now the bracket is a little on the short side, so we have to make it a little bit longer. What we're going to do is just add a couple more holes to the end of the bracket. more
8/13/2012 10:33:56 PM
Gooseneck Trailer Hitch Installation - 2012 Ford F-350 4448- Video
Today on our 2012 Ford F350 we're going to be installing the Draw-Tite Hide-A-Goose 30K Gooseneck Head, part number 9460 in conjunction with the Gooseneck Mounting Kit, part number 4448. Now we've already gone ahead and removed the spare tire from the vehicle so our next step will be to remove the exhaust. We'll need to unbolt the hangers from the frame of the truck as we'll need to install hanger extensions before reinstalling our exhaust we'll undo the rear hanger here undoing the 1/10-mm bolt on the bottom side of the frame as well as the 10-mm bolt on the inside of the frame rail. We can then move forward on the truck and undo the two 13-mm nuts holding that hanger in place. They do face up towards the bed of the truck. It is quite a tight fit to get those undone. more
6/19/2012 6:56:23 AM
Snap-Loc E-Track Tie-Down Anchor Installation - 2003 Ford F-250- Video
On this 2003 Ford F250, we're going to be installing the snap lock tie downs part # SLB25. To install this tie downs, we'll also use the hardware kit part # SLHZ. The first thing we need to do is position our snap locks on the bed of our truck. We'll take a paint marker and use it to mark our drill holes. Once we have our snap locks marked out, we'll go ahead and take a drill and drill out our holes. We also want to make sure that on the underside of the bed, we're not going to drill under anything like fuel lines or electrical systems. more
6/6/2012 6:52:37 AM
Trailer Brake Controller Installation - 2011 Ford Ranger- Video
Today in our 2011 Ford Ranger we are going to be installing the Prodigy P2 Brake controller, part number 90885 in conjunction with the ETBC7 wiring kit for our new simple harness which will be mounted with the no drill bracket from Draw-Tite, part number 18136. To begin our installation we are going to start here at the back of the vehicle. Go ahead and wire up our bracket and start running our new duplex cable to the front of the vehicle. As you can see this vehicle is already equipped with a four pole harness. Before we can install our seven-pole well need to go ahead and attach the mounting bracket. Well use some supplied hardware then once we get all four fasteners in position well go ahead and tighten them down. more
6/6/2012 6:50:18 AM
Pilot Automotive Navigator Off Road Light Installation - 2003 Ford F-250- Video
All right. Today on this 2003 Ford F-250, we're going to install part number NV-802C. Now, well actually be installing four of these on this vehicle. Well also be using the wiring kit, part number A-720. We're going to start off by installing the switch base onto a removable panel, that's below the steering column. Now, to transfer the pattern from our switch onto the backside of the panel. more
6/4/2012 4:13:30 PM
Yakima Roof Rack Fairing Review - 2011 Ford Fiesta- Video
Today on our 2022 Ford Fiesta 5-door Hatch Back, were going to test fit the Yakima 44-inch Roof Rack Fairing part number Y07048. To attach the fairing, well fit the clips around our round crossbars. Once we have the fairing clipped on and in position well take the wing nuts to tighten down the two outer clamps. With that the fairing is installed and were ready to hit the road. That does it for our test fit of the Yakima 44-inch Fairing for Roof Racks part number Y07048. more
3/26/2012 10:08:15 AM
Trailer Brake Controller Installation - 2008 Ford Explorer- Video
Today, on this 2008 Ford Explorer, we're gonna install a Prodigy P2 Brake Controller part number 90885. We're also gonna be installing the ETBC7 kit or part number ETBC7 and Tow-Ready Mounting Bracket part number 118136.First, we'll take our Tow-Ready Bracket and our 7-Pole and we'll install them together. Simply using the hardware that comes with our bracket then we'll go ahead and tighten our screws down.Now we assembled our bracket mounting to our tow-ready bracket, we have the option of mounting it here on our new hitch or we're actually gonna mount it here on the manufacturer's hitch.With our bracket in place, we take our band clamp, comes with the bracket install kit.Go ahead and wrap it around the bracket and the hitch.Once you get your bracket positioned where you want it and your band in place, you can go ahead and tighten it down.Say we've got a little bit leftover here from our clamp, Im just gonna take a pair of tin snips and cut it off.Alright, with our 7-pole bracket mounted, Im gonna go ahead and install a new 7-pole and 4-pole connectors. It comes with our ETBC7 kit. Im just gonna use our provided kit for the mounting. First Ill feed my wires through the bracket. more
12/30/2011 9:13:00 AM
TracRac Cantilever for G2 Ladder Rack Installation - 2006 Ford F-150- Video
Today in this 2006 Ford F150 with an eight-foot bed were going to add cantilever over the cab extension part number TA44000-02. Well be adding this to our tack rack kit TA21000-02. In order to add our cantilever kit we need to replace the sidles on our existing rack. What well do is go ahead and remove the bolt for the cross bar and then remove the bolt for the sidle unit. Then repeat the same process on the passenger side. Now we got our tension points loosen up. more
12/21/2011 8:10:10 AM
Trailer Brake Controller Installation - 2004 Ford E-450- Video
Alright today on this 2004 Ford E450 thats an RV, were going to install a brake controller part number 90915. We will be using an adapter cord 3035-P, and on the back of the vehicle well be using 4 pole to 7 pole adapter part number 37185, and also a bracket to hold everything together 118140, and with these parts well fill in the gaps that are missing on part of this tow package. Okay we are going to start off by working on the rear of the RV and working our way forward. What we are going to do is actually remove the 5 pole connector that is located on the hitch right now. Were going to disconnect that and add a new connector to the back of the vehicle, and that part number will be adapter part number 37185, and we will also be using an adapter bracket part number 118140, and we will start with that part. This is the adapter bracket; we are going to mount to the bottom by clamp to hold it in place. more
11/4/2011 5:59:06 PM
Trailer Brake Controller Installation - 2004 Ford F-150 3035-P- Video
Today we are working on a 2004 Ford F-150. We are going to be installing the Tekonsha Prodigy P2 brake controller, part number 90885-3035P. Our first step in installing our brake controller will be locating the plug to plug our connection into on the manufacturer side. Here, up under the dash above the brake pedal, there is a gray plug that will match up perfectly with our wiring harness. Now that we have our wire harness connected to the manufacturer harness, we are going to go ahead and mount our brake controller. 0:36 more
9/20/2011 10:45:31 AM
Thule Tracker Roof Rack Foot Pack Installation - 2001 Ford Escape- Video
Today on this 2001 Ford Escape we are going to install a Thule AeroBlade and Rapid Tracker 2 roof rack system. First we are going to install our Tracker fit kit into the factory side rails of our Escape. We will measure from the front of the track to the front edge of our fit kit on both the driver and passenger side to make sure they are even with each other and then tighten them down. Next we will put the rear fit kits into place but we are going to leave these loose. 0:32 more
9/20/2011 7:59:45 AM
Trailer Brake Controller with Wiring Installation - 2000 Ford F-250 Super Duty- Video
Today on this 2000 Ford F-250 Super Duty we are going to install part number 90885-3035P. The Tekonsha Prodigy P2 brake controller with the adapter cord that will plug into the factory Ford outlet. The first thing we need to do is get access to the port near the panel underneath the steering wheel that we have to temporarily remove. You can simply use a coin to undo the latches. Right here is the port that we need to plug into. That is kind of hard to get the wire harness in there and plug it in so you can use a screwdriver or a trim panel tool like we are using and just pop it up a little bit, get underneath of it and pop it loose so you can get a better angle at it. Take the cord and plug it in and take the cable and route it below and put the panel back into place. 00:55 more
1/19/2011 1:41:41 AM
Thule Tracker II Roof Rack with Kit Review- Video
Today we are going to install a Thule Tracker II Roof Rack on this 2006 Ford Escape. Using the Thule Tracker II Foot Pack part number TH430R, the fit kit part number THTK1, and the Thule Rapid Air Load Bars part number THRB43. The first step in preparing the roof rack is to loosely assemble the hardware with the bases. Depending on your vehicle application not all of the hardware is going to be used. However on the Escape we are going to need all of them. Through the top of the base we are going to our bolt with the thread locker on it as well as the washers. They do go in a certain order. The yellow zinc coated washers go in first, then the thinner black washer, and then we will in the bolt. 00:43 more
11/15/2010 10:49:03 AM
Fifth Wheel Installation - 1999 Ford F-350- Video
Today on this 1999 Ford F-350 super duty, we are going to install part number RP50082. The first thing we need to do is go ahead and lower the spare tire so we have access underneath the vehicle. And then once we have that done, we will go into the bed of the truck and we will start marking out the places for our rails. What we are going to do is measure out from the edge of the bed itself, not the tailgate but the bed, and we are going to measure out and place a mark in the bed as described in the instructions. We are going to do that in two places on both sides. Now we have our mounts in our bed. We will line up our first rail and you are going to want to get them even left to right, using the seam right here works out pretty good. Our custom install kit on the bottom is going to use these two outside holes here. So we will find the center and mark that. Do that on both sides of the rail. Alright, let us move our rail out of the way. We will go ahead and drill a couple 1/8 inch holes. Now we are by the frame of the vehicle on the driver side. Now you do not want to really have to take off the back tires but we did anyway for clarity. One thing we know is that our plate is going to have to sit flat on the frame so that our brake cable here is going to be in the way. So, we are going to move that out of the way. There will be a provision to but that back on later on. 1:12 more
9/30/2010 6:03:15 AM
Fifth Wheel Hitch Installation - 2002 Ford F-250- Video
Today on this 2002 Ford F-250 we are going to install part number RP30035 from Reese. For the first part of the install we need to locate the rear base rail for the fifth wheel hitch. Our measurement is going to start at the very end of the bed itself, not the tailgate, the end and we are going to measure up as described in the instructions. And then we will go ahead and make our mark. We will do that on both sides so we can make our rails even. :25 more
8/18/2010 1:41:24 AM
Trailer Brake Controller Installation - 2009 Ford F150- Video
Today we are going to install a Prodigy Brake Controller, part number 90185 on our 2009 Ford F-150, and we are going to use the accompanying brake control adapter and show you how it gets installed. This is a little bit different from previous models. The plug for the brake controller is actually behind this tray right here. What happens is, this panel comes off, and then we get behind the tray - unscrew the tray - and the connection is right behind it. All right, what we are going to do first is go ahead and just take off this panel right here. And it is actually pretty easy. Just give a gentle pull on the bottom and just work your way up. And start on the right-hand side, so that way you can pull it out from underneath this piece here. When you do pull on this, this little panel here will come back toward you, too, and give you a little bit of extra room to pull it out. more
2/16/2009 10:17:32 AM
Trailer Brake Controller Installation - 1996 Ford Explorer- Video
Today we are going to install part number 90195 from Tekonsha, the P3 Brake Controller. We are also going to install along with it part number ETBC7. And this will all be installed on a 1996 Ford Explorer. To begin our install, we are actually going to start with the rear of our vehicle and then work our way forward. First off, we are going to install our bracket that actually holds our 7-pole in place. There are substitute brackets that you can use that this will go onto and mount onto the hitch tube itself. However, this particular 7-pole does not really work that good you have to get some extra-long screws and make new holes in the bracket. But in this case, it makes things a little easier and probably a little bit nicer. So we will go ahead with this bracket here that comes factory with it. We will drill out a half-inch hole, which will work perfect with the carriage bolt with a half-inch square hole in the bottom of the bumper. And we will end up with the bracket about right there. We have got our bracket in a bench vise and we will go ahead and put in a quarter-inch pilot hole first and follow it with a half-inch bit. We will our bolt into the bumper and then we will go ahead and install our bracket. And then we will put on the nut and then tighten it down and use an extra hand to hold the bracket while you tighten down the nut and bolt. All right, we will go ahead and install our 7-pole into the bracket. more
2/3/2009 9:30:30 AM
Trailer Brake Controller Installation - 2006 Ford Ranger Part 2- Video
This is the second video showing the final steps required to install the Tekonsha Prodigy brake controller on the 2006 Ford Ranger truck. It can sound like a lot of work but finish watching the video, you will see it really is not as hard as it may sound. You will see where the brake controller is actually mounted in the drivers area and how the connections to the battery are made more
8/6/2008 6:15:44 AM
Trailer Brake Controller Installation - 2006 Ford Ranger- Video
We show you here how to hardwire your vehicle with an electric brake controller. We are using the popular Tekonsha Prodigy and using our Brake Controller 7 and 4 Way Installation Kit, ETBC7, to set this 2006 Ford Ranger up to tow a trailer with electric brakes. Even though the truck is not pre wired to accept a brake controller it can be done allowing you to safely tow campers, utility trailers, horse or livestock trailers and more. more
8/6/2008 6:12:45 AM
Trailer Brake Controller Installation - 2003 Ford F250- Video
Just to give you a reference point, this is the top, right here of the gas pedal, so basically its across up on this pillar here. While were here well plug in our brake controller adapter and that will be part # 3035-P. Now we can plug the other end of this into our brake controller after we install the mounting bracket. Next well mark our bracket for positioning, well just hold it up here on this bottom edge where its nice and flat. In this corner right here, well just make a small dot for reference and then well put our first screw there. Afterwards well put our brake controller inside and eyeball it to make sure we get it straight. When we have positioned the way we want it, we ll make our secondary screw install here. Okay at this point we can simply install our adapter cable in then well just mount right here. We have the brake controller installed now, the last thing we do is take the wires and zip tie them into a safe position and all we have to do is test. more
7/22/2008 9:21:09 PM
Filter Videos
Filter Videos
