What are the Measurements of the Demco # DM8759131 Brake Actuator

Question

Question:

I MAY HAVE A MOUNTING PROBLEM DUE TO TOUNGE LENGTH AND THE LOCATION OF MY JACK WHICH IS WELDED ON... CAN YOU SUPPLY ME WITH OVERALL UNIT DIMENSIONS AND HOLE SPACINGS SO THAT I CAN DETERMINE WHETHER MOUNTING CAN BE DONE WITHOUT MOVING THE JACK OR MODIFYING THE TOUNGE?

asked by: MILES

0

Expert Reply:

I went to our warehouse to get the Demco brake actuator and provide you several measurements.
The overall length is 23-3/4 inches and 5-3/4 inches from the channel to outer housing. The 3 center eye to eye measurements are 1.34 and 2-inches on the channel and each pin hole is .65 inches in diameter. The mounting flanges below the outer housing measurements are 3-inches from eye to eye on the mounting flange with 2 pin holes. Each of these mounting holes are .52 inches.

I included a diagram to the right and a video for you to look at.

expert reply by: Chris B

0

click to enlarge

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 3

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 6

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

Hey Kevin, for your Demco DA70 actuator you can use the Reverse Lockout Solenoid for Demco Hydraulic Brake Actuators #DM11993.

view full answer...

What are the Measurements of the Demco # DM8759131 Brake Actuator

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching