Components Needed to Flat-Tow 2013 Fiat 500 using SMI Stay-IN-Play DUO

Question

Question:

What components are needed for a Fiat 500 Pop? Is there a video of an installation on a Fiat 500? Thanks

asked by: Randy H

0

Expert Reply:

First thing you will need to flat tow your 2013 Fiat 500 Pop is a base plate kit. For that you would want the Roadmaster EZ2 Base Plate kit part # 522013-1A.

In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat tow your vehicle. The most popular compatible tow bar is the Falcon 2, # RM-520. For safety cables you can use # RM-643. The coiled design helps keep the cables off of the ground.

For lighting you can use the bulb and socket kit, # RM-155, and not have to worry about cutting and splicing into the vehicle wiring.

And finally, most states now require supplemental braking in the vehicle being flat towed. The easiest system to set up and use is the Even Brake proportional system, # RM-9400, that applies the vehicle brakes in proportion to how much the two vehicle is braking. This is the safest way to stop and it reduces wear and tear on both vehicles.

I have included a couple of helpful links to our articles on flat towing for you. Be sure to consult the vehicle owners manual for more specific information on flat towing your vehicle.

expert reply by: Jameson C

0

Answer 1

The first thing you'll need to flat tow your 2015 Chevy Malibu LS is a base plate kit like the Roadmaster part #RM-523178-5 that is a confirmed fit. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting,…

view full answer...

Answer 2

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 3

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Ken, so the first thing you will need is a base plate kit like the Blue Ox part #BLU85CR which fits your 2023 GMC Canyon and would be compatible with your Blue Ox tow bar. I do not know what braking system you had in the past but for a permanent…

view full answer...

Answer 7

Hello Curtis. You can absolutely use an RV mount tow bar with your 2006 Ford E350 Van. For example, the Blue Ox Avail Non-Binding Tow Bar #BX7420 is compatible with any 2" hitch receiver. This could be on a motorhome, van or pickup truck. As…

view full answer...

Answer 8

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Answer 9

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 10

The instructions for the Demco Tabless Base Plate Kit #DM77YV are being added to page but I'll also send them to you separately. In the instructions they only show that the air dam needs a chunk cut out and that the shutters would remain. The…

view full answer...

Answer 11

What you need is a light kit specifically for flat-towing. The Plug-N-Tow TM Vehicle Wiring Harness, #42615, would be if the Jeep were towing a trailer and not for activating its lights while it is being towed. There are a few options for lighting…

view full answer...

Answer 12

We do offer tow bar setups that can attach to the D-rings on the Warn Elite Bumper. Your will need to use a D-ring adapter to connect the tow bar. For the adapter you have the following options: 1" Thick D-Rings #RM-035-1 3/4" Thick D-Rings…

view full answer...

Components Needed to Flat-Tow 2013 Fiat 500 using SMI Stay-IN-Play DUO

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching