Trailer Hitch Receiver Recommendation for 2004 Toyota Tacoma
Question:
37042 Will it fit my 2004 toyota tacoma
asked by: Tony
Expert Reply:
When it comes to a trailer hitch for your 2004 Toyota Tacoma, I recommend going with the Draw-Tite Class III Receiver Hitch, # 75078. This is a custom fit hitch that bolts directly to the frame of your Tacoma with no welding required.
I am also including a link to the other hitch receivers that are available for your Tacoma.
Part number 37042 is a discontinued hitch but I was able to obtain a bit of information and it is not listed as a fit for the 2004 Toyota Tacoma.
If you plan on towing with your Tacoma, you might also need the following:
Trailer Wiring Harness, # 118379
Ball Mount, # D-4
Pin and Clip, # PC3
1-7/8 Inch Trailer Ball, # 19260
2 Inch Trailer Ball, # 63845
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 5500 lbs WD GTW
- 2 Inch Hitch
- 550 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Choose the Right Trailer Hitch Class
- Article: Rust Prevention
- Article: How to Measure for Trailer Hitch Drop
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Hidden Hitch Recommendation for a 2002 Toyota Tacoma
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Hitch Installation Tips
- Q&A: Replacement Hardware Kit for Draw-Tite Class III 2 Inch Hitch # 75078 on a 2004 Toyota Tacoma
- Q&A: When Does Trailer Sway Control Allow Backing Up Trailer
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Comparing Draw Tite and Curt Hitch for 2006 Toyota Tacoma
- Q&A: Will Curt C51108 Echo Pass Through 12-Volt Power to Maintain Trailer Mounted Battery
- Q&A: 7-Way Recommendation for 2001 Toyota Tacoma with Reverse Light Circuit Active