Replacement Spindle Washer for an EZ Lube Spindle

Question

Question:

I need an easy lube spindle washerfoot for a 2002 Foster trailer 10,000 GW. Do you sell separately? Thank you.

asked by: Walt

0

Expert Reply:

We have several styles of spindle washers available. To see them all check out the link I attached to the right. You will need to pick the style that's as close to yours as possible.

expert reply by: Jameson C

0

Answer 1

A replacement tang-style spindle washer like part #5-101 is intended to be installed behind the castle nut and have its prongs bent down so that they prevent the castle nut from rotating on an E-Z Lube type spindle. The castle nut holds the washer…

view full answer...

Answer 2

You'd want the tang washer like the #5-101 that you referenced between the washer and the nut.

view full answer...

Answer 3

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub…

view full answer...

Answer 4

I don't have any information available that would tell me which bearings your trailer used, but I can certainly help you figure it our for yourself. Closely examine the old bearings, looking for a part number engraved on the bearing cage. Get…

view full answer...

Answer 5

There is no specific torque rating for the castle nut that holds your hub in place. We recommend tightening the castle nut down until it stops, and then backing it off to the next notch wheel the tang washer will fit into the castle nut. Over…

view full answer...

Answer 6

The Replacement Spindle Washer - Tang Type for E-Z Lube #5-101 is the correct fit for your trailer spindle based on the picture and measurement if you want to use a castle nut like #165686. The alternative option is the Spindle Nut Kit for EZ Lube…

view full answer...

Answer 7

The Replacement Spindle Washer #5-101 referenced in your question is designed for 1 inch, D type spindles. The washer will install right between the castle nut and outer bearing, and the tang on the washer is bent up to prevent the nut from turning.…

view full answer...

Answer 8

As you may have already found, 5200 lb, 6000 lb and 7000 lb axles can all use the same components including inner/outer bearings, hubs and brakes. Here are some other things they share in common: Dexter 5200 lb Regular Duty Axle - 0.180 inch tube…

view full answer...

Answer 9

The TruRyde Replacement D Tang Spindle Washer #5-101 that you referenced has a 1-inch inner diameter to fit on 1-inch diameter spindles. All such items that we offer share this same 1-inch inner diameter, such as parts #5-23 and #5-57. The points on…

view full answer...

Answer 10

There really should be a flat washer between the outer bearing of your hub and the nut that holds it on. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut. The Washer For 1 inch Spindle,…

view full answer...

Answer 11

I ran out to the warehouse and pulled one of the battery boxes off the shelf, and took several measurements off of it. If you refer to the photo I have edited, you can see the dimensions of the outside of the box.

view full answer...

Answer 12

The battery that fits in box #TN65117 measures 3.54 inches long, 2.76 inches wide, and 3.93 inches tall. Including the terminals it is 4.17 inches tall. A battery that is at most these dimensions or smaller would fit in the box. It is designed as a…

view full answer...

Replacement Spindle Washer for an EZ Lube Spindle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching