Hitch Recommendation for a 2014 Subaru WRX STi For Towing Two Motorcycles
Question:
Just a few questions for you guys, do you have any installed photos from the underside of the car? I have a 2014 Subaru WRX with an aftermarket quad exhaust I saw one vehicle with an SPT exhaust but mine is not that brand. An underside photo would help me get some idea of if it will work or not. Also, would this hitch be able to tow a small trailer with two motorcycles and various equipment? I see lots of folks using them for bicycles but no mention of motorcycle towing. Thanks!
asked by: Paul
Expert Reply:
I wish we had a picture I could show you of the underside of a vehicle with the Curt Hitch part # C11120 installed. The best I could do is have you check out the installation instructions link I attached to the right. You should be able to get a pretty good idea whether or not the exhaust you have is compatible with this hitch.
As long as you stayed under the capacity of the hitch and your vehicle you should have no problem towing a small trailer.
For trailer wiring you would want the part # 119250KIT, ball mount part # C45521, pin and clip part # F-4, 1-7/8 inch ball # A-80, 2 inch ball # A-82.
Products Referenced in This Question
ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Universal Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- CURT
more information >
2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- CURT
more information >
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Curt Hitch Pin and Clip for 1-1/4" Hitches - 1/2" Diameter x 2-1/2" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- 2-1/2 Inch Long
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- 2-1/2 Inch Span
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Trailer Hitch for a 2013 Subaru Impreza 5-Door WRX with Factory Quad Exhaust
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: How to Carry a Dirt Bike on a 2017 Subaru WRX
- Q&A: Availability Of A 1-1/4" Draw Bar And 1-7/8" Ball With 0" Of Rise
- Q&A: Differences Between Kuat Sherpa 2.0 and Older Sherpa, Comparison to Thule T2 Pro Xtr
- Q&A: How To Upgrade Speed Rating Of 40x48 Ironton Utility Trailer
- Q&A: What Trailer Hitch Will Fit a 2011 Subaru Impreza WRX with Dual Exhaust
- Q&A: Can the etrailer Trailer Hitch Cargo Carrier be Used with a 1-1/4 to 2 Inch Hitch Expander Adapter
- Article: Best Bike Racks for Electric Bikes
- Article: Trailer Hitch Installation Tips
- Article: How to Measure for Trailer Hitch Drop
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Rooftop Cargo Carriers
- Article: 5 Things to Know About Weight Distribution Hitches