2013 Nissan Altima 4 Door Sedan Hitch Recommendation
Question:
Hello: I have a 2013 Nissan Altima 4 door sedan and am thinking of buying a trailer hitch from you. Do you have anything that does NOT require heat shields removal? Any drilling? Thanks.
asked by: Guy
Expert Reply:
The Draw Tite Hitch part # 24796 would be an excellent choice as a hitch for your 2013 Nissan Altima. There will be a little bit of drilling required, but the heat shield will not need to be removed. Check out the install video I attached for this hitch.
To complete your towing setup you may also be interested in the following:
Ball mount # 3594
1-7/8 inch ball # 19256
2 inch ball # 19258
Trailer Wiring Harness part # 118470
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 4 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Trailer Wiring Diagrams
- Article: Troubleshooting 4 and 5-Way Wiring Installations
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Q&A: Troubleshooting Trailer Lights Which are Not Working
- Q&A: Correct Replacement Oil Seal 225255UC for Ranger Boat Trailer
- Q&A: Replacement for a TDE LP8500 Boat Trailer Acuator
- Q&A: Are 1/2-20 Lug Nuts Able To Be Used On M12-1.5" Wheel Studs?
- Q&A: Replacement Studs for RVD-H-865 7k Hub/Drum
- Q&A: Replacement Bearing and Seal Kit for 2004 Kendon Motorcycle Trailer
- Article: How to Survive the Winter In Your RV
- Article: How to Choose the Right Trailer Hitch Class
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)
- Q&A: Necessity of Using Lift or Jack Stands to Install Receiver Hitch on 2005 Dodge Caravan