Which Spindle Will Fit 6 on 6 Dexter Hub Part 42660UC1

Question

Question:

Which Spindle do I need to purchase with this hub part #42660UC1 this assembly is for a homemade heavy duty trailer

asked by: Jerry

0

Expert Reply:

The correct spindle for Dexter hub, part # 42660UC1, is spindle part # TRU57FR or EZ Lube spindle part # TRU37FR.

There are other 6 on 6 hubs that you could use if you want heavier spindles. How much weight are you wanting each axle to hold? How many axles?

expert reply by: Patrick B

0

Answer 1

For an agriculture hub designed for a 6k axle with a 6 on 6 inch bolt pattern you would want the part #42660UC1. For the matching spindle for this hub you would want the number 42 spindle part #TRU57FR.

view full answer...

Answer 2

Based on what you listed the replacement hub you need is the part #42660UC1 as it has the 6 on 6 inch bolt pattern and uses the same bearings you have as well.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

The Trailer Hub and Drum Assembly part #AKHD-545-35-K is the correct replacement for an AL-KO 7230. In regards to the braking assemblies, I suggest getting a new pair, the Electric Trailer Brake Kit part #AKEBRK-35-SA. This option will save you some…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Which Spindle Will Fit 6 on 6 Dexter Hub Part 42660UC1

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching