Will the Dust Cap Driver Tool part # 290-992 Work On EZ Lube Spindles

Question

Question:

Will the dust cap driver -Dust Cap Driver Tool - Medium - for 2.440inch OD Grease Caps - fit over the dust caps for EZ Lube axles with the rubber plug, or just the solid caps? Thanks

asked by: Victor

0

Expert Reply:

As long as the dust cap on your hub has a 2.44 inch outer diameter the Dust Cap Driver Tool part # 290-992 that you referenced would work for your cap regardless if it is for a EZ lube spindle or non-EZ lube spindle.

I attached a review video for you to check out as well.

expert reply by: Jameson C

0

Answer 1

The closest thing we have to a 2-3/8" outer diameter is the Grease Cap - 2.446" Outer Diameter - 1-5/16" Tall - Drive In #F001520. I recommend using a digital caliper like the #PTW80157 when measuring to ensure accuracy. If you find…

view full answer...

Answer 2

This actually happens with vehicles that use an auto-leveling system pretty often. Disengaging this system while towing will definitely help as it will allow your weight distribution system to have more tension on the bars, which will help with sway.…

view full answer...

Answer 3

The Tuson Electronic Sway Control System for Electric Trailer Brakes #335TSC-1000 has installation instructions that give a placement location on the center of your trailer and 5-10 feet behind the hitch ball. The unit comes with a wiring harness so…

view full answer...

Answer 4

I have heard of similar issues and the culprit is often that the Trailer Sway Control System on your 2015 Toyota Tundra is fighting the Tuson Asymmetric Sway Control #335TSC-1000 that you have on your Safari Condo Alto 2114. This is not normal and…

view full answer...

Answer 5

The correct bearing kit for your 7,000 pound Lippert axle is #BK3-210.

view full answer...

Answer 6

The correct grease cap for the Dexter Trailer Hub and Drum Assembly for 8,000-lb E-Z Lube Axles #DX46XR is the #TRU66FR.

view full answer...

Answer 7

EZ Lube Dust Caps, like #DC200L-DCRP, have a rubber plug that can be removed to access the zerk fitting. The rubber plug can be removed by gently prying it up with a flathead screwdriver. If your dust cap is in good condition and you want to avoid…

view full answer...

Answer 8

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 9

The only difference between the two hubs is the inside dimension of the grease seal included with the hub drum. The #42866UC3-EZ uses a 10-36 grease seal with a 2.25 inch inside diameter and the #8-219-4UC3-EZ uses a 10-10 grease seal that has a…

view full answer...

Answer 10

In order to get the correct replacement seal you will want to remove the seal from your hub and get the number stamped on it. If you can't find the number you can also use the dimensions of your seal to get the correct replacement. Get the outer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Heavy duty ramp springs #RS16933RH and #RS16933LH install on the hinge of the ramp. I have included a picture of what this looks like for you. Not all trailers are exactly the same but this should give you a general idea of how the springs install.

view full answer...

Will the Dust Cap Driver Tool part # 290-992 Work On EZ Lube Spindles

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching