Long Ball Mount for 2 inch Trailer Hitch with 4 Inch Drop and 13 Inches Clearance
Question:
I have the hitch BM20 with a 2inch drop and my tandem trailer rides about level. Can I switch to the 4inch drop and does trailer have something similar to bm20- 13inch long is my length needed. Will lowering this much impact my rear tires since it will now be 2inch lower? I think the 2inch drop may help with gas mileage?
asked by: Jim N
Helpful Expert Reply:
Curt ball mount # C45270 does have a 4 inch drop and measures 13 inches from the center of the hitch pin hole to the center of the ball hole. It is rated for 750 pounds tongue weight and 7,500 pounds gross trailer weight.
And we also have ball mount # EA40 which has a 4 inch drop and measures 14-5/8 inches from the center of the hitch pin hole to the center of the ball hole. It is rated for 800 pounds tongue weight and 8,000 pounds gross trailer weight.
You will want to tow the trailer as level as possible. Having too much tongue weight with the trailer angled down at the front could cause sag at the back of the tow vehicle and cause the front to ride high affecting steering, braking, and visibility.
I have included a link to a help article that shows how to measure for the right rise or drop to tow a trailer level.
Products Referenced in This Question
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 4 Inch
- Rise - 2 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Long Shank
- CURT
more information >
Brophy Ball Mount - 3" Rise, 4" Drop - 14-5/8" Long - Aluminum - 8,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Aluminum Shank - Silver
- Drop - 4 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 8000 lbs GTW
- Class IV
- Long Shank
- Brophy
more information >
Product Page this Question was Asked From
Brophy Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 13-1/4" Long - 10K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 0 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Class IV
- Brophy
more information >
Continue Researching
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Safety of Using Hitch Extender and Other Options To Clear Spare Tire on Jeep Liberty
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Q&A: Difference Between Brophy # BM20 and # BH20 Ball Mounts
- Q&A: Will Extreme Ratcheting Trailer Jack Keep Moving Forward without Handle if in Forward Position
- Q&A: Stowed Length of ARK ORJW1SU Off Road Trailer Jack
- Q&A: Extended and Retracted Height of ARK ORJW1SU Extreme Off-Road Ratcheting Trailer Jack
- Q&A: What is the Diameter of a ST225/75R15 Tire in Centimeters
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Is the Thermostat for the Advent # ADV94FR Air Conditioner Wireless?
- Article: Hitch Adapters and Extenders
- Article: The Best Boat Bumpers
- Article: How to Choose the Right Trailer Hitch Class
- Article: 5 Things to Know About Weight Distribution Hitches