Looking for a Ball Mount with More Rise for a 2014 Ford Fusion
Question:
Have a 2014 Ford Fusion Titanium with 4 wheel drive rate to tow 2,000 pounds. Insert bar 2 Inch ball for 2 inch receptacle on receiver has rise 2 ?. However the rise is NOT high enough. Chains drag need to be wrapped around trailer tongue. IS There an bar with MORE than the 2inch rise?
asked by: Robert D
Expert Reply:
We have several ball mounts with a rise greater than 2 inches. I have attached a link to our ball mount page for you to check out. I am not familiar with a trailer hitch with a 2 inch receiver for the 2014 Ford Fusion. There are Class II hitches with 1-1/4 inch receivers, is that what you have?
If you have a Class I or Class II trailer hitch, I strongly recommend checking the installation instructions or with the hitch manufacturer to verify ball mount compatibility. Most trailer hitch manufacturers require a specific ball mount to be used with Class I and Class II trailer hitches because that is the only ball mount they test with the hitch.
If you can tell me the brand and Class of your trailer hitch, I would be happy to give you a more specific ball mount recommendation.
Product Page this Question was Asked From
Brophy Drawbar for 1-1/4" Hitches - 5-1/2" Rise, 6" Drop - 7-1/4" Long - 3.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 6 Inch
- Rise - 5 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- Brophy
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: BOLT brand vehicle and hitch locks
- Article: Trailer Hitch Receiver Sizes
- Q&A: Recommended Ball Mount for a Mercury Mountaineer With 1-1/4 Inch Factory Hitch
- Q&A: Ball Mount to Use with Draw Tite Hitch for 2012 Mazda 3
- Video: Curt Hollow Shank Accessories Anti-Rattle Kit Review
- Video: Brophy Drawbar Review
- Video: Brophy Ball Mounts - Fixed Ball Mount - BM96 Review
- Shop: Pin and Clip for 1-1/4" Hitches - 1/2" Diameter
- Shop: Curt Hitch Pin and Clip for 1-1/4" Hitches - 1/2" Diameter x 2-1/2" Span
- Shop: Curt Hitch Pin and Clip for 1-1/4" Hitches - 1/2" Diameter x 2" Span - Plastic Grip
- Shop: Trailer Hitch Anti-Rattle Kit for 1-1/4" Trailer Hitches
- Shop: Brophy Anti-Rattle Drawbar, 1-1/4" Hitch, 5-1/2" Rise / 6" Drop, 7-1/4" L, 3.5K
- Shop: 2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Shop: Brophy Drawbar for 1-1/4" Hitches - 5-1/2" Rise, 6" Drop - 7-1/4" Long - 3.5K
- Video: Choosing the Right Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: hitch
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: Does Truck with 6-1/2 ft bed Have to Use Slider Hitch for Turning Clearance with Fifth Wheel Hitch
- Video: Choosing the Right Brake Controller
- Search Results: hitch pin
- Shop: Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Suspension Enhancement
- Search Results: locking hitch pin
- Shop: Gooseneck Hitch
- Q&A: What Is An OEM Prep Package And How Do I Know If I Have It