What is the Distance from Ground to Center of Bracket with Trailer Valet Jack and Mover Installed

Question

Question:

Can you give me the dimension of the Valet at its lowest height, the distance from the bottom of tire and the center of the mount on the trailer side rail. I need to know this because my trailer tongue needs to be low when I move it in a tight area.

asked by: John G

0

Expert Reply:

We have a Trailer Valet, # STC-V211, installed on a trailer outside so I lowered it as far as it would go. I then measured from the ground to the center of the mounting bracket and it is approximately 11 inches. I was actually surprised at how low it went. To the bottom of the bracket it was approximately 9 inches.

expert reply by: Michael H

0

Answer 1

In regards to the Trailer Valet 5X Swivel Jack and Trailer Mover part #STC-V211, the distance from the bottom of the wheel or ground to the center of the mounting point is 11" while fully retracted.

view full answer...

Answer 2

I checked with Trailer Valet and the height range of the frame bracket of the Trailer Valet RVR3 part #TVRVR3 is between 13.5 inches and 20 inches.

view full answer...

Answer 3

You can try using a trailer dolly like the Rack'Em #RA20 rated for 500 lbs Tongue Weight (TW) but 3,400 lbs is quite a lot to move by hand. I recommend using a Trailer Valet to assist you in moving the trailer which makes it much easier. The 5X…

view full answer...

Answer 4

I have an answer for you. Unfortunately, you will not be able to use the Trailer Valet 5x #STC-V211 with a ball base attachment to use it on a hitch. However, if you want to attach your jack to a coupler, I recommend the Trailer Valet XL Trailer…

view full answer...

Answer 5

The Trailer Valet 5X Swivel Jack and Trailer Mover #STC-V211 has a bracket height of 9 inches retracted and 24 inches extended with the 15 inch lift. Depending on the mounting location of this swivel jack you should be able to get the tongue down to…

view full answer...

Answer 6

I went to our warehouse and took some measurements of the Trailer Valet 5X, part #STC-V211 for you. I have attached a photo of the #STC-V211 with the dimensions noted. From the top mounting bolt on the mounting bracket to the top of the handle it…

view full answer...

Answer 7

I have a solution for you, but there is not an available extension tube available for the Trailer Valet XL #TVXL25. I would instead recommend using the trailer dolly/jack with the highest lift we have available, which is the 24" tall Trailer…

view full answer...

Answer 8

If you only have 1/8 to 1/4 inch of space to close your garage the Trailer Valet you'd need is the part #STC-V211 which attaches to the frame of the trailer because of that would not add additional length to your trailer which would reduce your…

view full answer...

Answer 9

I wasn't sure exactly what dimension you were looking for on the mounting bracket of the Trailer Valet part #STC-V211 so I attached a picture that has nearly every dimension for you to check out.

view full answer...

Answer 10

If you are looking for something that stays permanently attached to the trailer then the only thing we have is the Trailer Valet 5X #STC-V211 because it mounts directly to the frame and has a swivel feature for when you are traveling. You can also…

view full answer...

Answer 11

It sounds like you are referring to the security bolt which is part 21b in the attached diagram. The security bolt was designed to keep the Trailer Valet part #STC-V211 in place when the device is rotated to the stow position, and as an extra safety…

view full answer...

Answer 12

Yes, you can simply remove the Trailer Valet Swivel Jack #STC-V211 from its pipe mount by pulling the pin from the mount and it would slide right off. I attached a review video for you to check out as well.

view full answer...

What is the Distance from Ground to Center of Bracket with Trailer Valet Jack and Mover Installed

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching