Hole Dimension for Flush Mounting the Trailer D Ring # RR01C

Question

Question:

What size hole to I need to make so that this will be mounted flush to surface?

asked by: Rex L

0

Expert Reply:

You will need a 3 inch hole to mount the Trailer D-Ring, Light Duty Tie Down, item # RR01C, on your trailer.

expert reply by: Robert G

0

Answer 1

The diameter of each fastener hole is 5/16 of an inch. The overall dimensions of this D-Ring are 3-1/2 inches by 5 inches. The center to center distance between the each fastener hole is 2 inches, and a total of 4 inches between the outermost…

view full answer...

Answer 2

Yes, the Curt Anti-Rattle Kit for Hollow Shank #C69HR will hold up when pulling your equipment trailer. This will only work on ball mounts for a 2" receiver with a hollow shank. I feel the Blue Ox Hitch Receiver Immobilizer II #BX88224 is…

view full answer...

Answer 3

The Anti-Rattle Hitch Lock for Kuat Transfer Bike Racks part #HLT comes with a 1/2" diameter bolt/pin. It can be used in both 1-1/4" receiver tubes with a 1/2" hitch pin hole and because it threads into the shank on the…

view full answer...

Answer 4

I measured the Replacement Nut Retainer and Nut #Y90254 and have an included diagram with everything you will need. I will also mention that this is designed for use with the Yakima HoldUp bike rack with a 2" shank, like the #Y02443. The…

view full answer...

Answer 5

It sounds like the anti-rattle hitch bolt in your old Yakima ROC'nGate is causing issues by not tightening up all of the way. Assuming the bolt itself is what is bad you can just replace it with #Y8890200. When it comes to replacement parts…

view full answer...

Answer 6

It sounds like you are looking for a locking hitch pin for the vehicle and a locking pin for the trailer coupler. If that is the case I recommend the Reese Tow and Store Lock Kit part #RP7014700 because it comes with both size hitch pin locks…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex…

view full answer...

Answer 10

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Hole Dimension for Flush Mounting the Trailer D Ring # RR01C

Product Page this Question was Asked From

Continue Researching