Brake Controller Install on Class C Motorhome on a 2014 Ford E450 Van Cutaway Chassis
Question:
We have a 2012 Fourwinds 28Z class C motor home on a Ford E-450 Chassis. I need to install a brake controller. I understand there is a connector at the top center of the console where the connector is located in the cab. I have a 4 pin connector on the hitch. I am confused about what wiring I need to do to add a Tekonsha controller. I thought there was a video of a fairly simple install but when I went to look I could not find a new motor home install. What do I need to make this happen? Are there any additional instructions available? Thanks
asked by: Mark
Expert Reply:
The brake controller connector should be located behind the dash as shown in the accompanying photos. The Tekonsha Prodigy P2, part # 90885 would be an excellent choice of brake controller. The P2 is extremely easy to set up and to use, which is why it's one of our most popular brake controllers. You'll also need the # 3034-P brake controller adapter.
Usually, a Ford Van that's equipped with the 4-pole trailer connector won't have the brake controller output circuit ran to the rear of the vehicle, but the cutaway chassis models are sometimes equipped differently. Follow the wiring harness for the trailer connector from the rear bumper up to the driver's side frame rail, where it plugs into the wiring harness leading to the front of the vehicle. On the side of this junction closest to the front of the vehicle, look for a blue and an orange or red wire (you might need to peel back a bit of the wire loom). If the blue wire is present, it'll be the output circuit for the brake controller. The orange or red wire, if present is the 12 volt accessory circuit.
You'll need an adapter like part # 37185 to convert your existing 4-pole into a 7-way. The adapter would plug into your existing 4-pole, leaving four remaining wires. The blue wire would attach to the blue wire you found on the frame rail. The black wire could connect to the orange or red wire on the frame rail and the white wire would ground to the vehicle frame. The purple wire usually carries the reverse light circuit, but if not needed, the wire can be bundled up out of the way. Once this is installed, you can plug in the controller, and you should be good to go at that point.
If you don't find the blue and red or orange wire on the frame rail, you'll need to run your own output and 12-volt accessory circuit. You'll need a length of # 10-2-1 cable long enough to reach the vehicle battery from the rear of the vehicle. Connect the black wire from the cable to black wire on the adapter, and the white cable wire to the blue wire on the adapter. Route the cable under the vehicle to the engine compartment, being sure to avoid anything that's sharp, moving or hot. The white wire in the cable would go through the firewall to the brake controller. On the # 3034-P wiring adapter, you'll sever the blue wire, and connect it to the white wire from the cable. The black cable wire connects to the positive battery terminal via a # 9510 40 amp breaker.
I'll link you to an FAQ article that explains the process.
Products Referenced in This Question
Deka Jacketed 2 Wire, 10 Gauge, Brake Wire - per Foot
- Wiring
- Wire
- Jacketed Wire
- 2 Wire
- 10 Gauge
- Deka
more information >
Adapter 4-Pole to 7-Pole and 4-Pole
- Trailer Wiring
- Wiring Adapters
- Multi-Function Adapter
- 4 Flat
- Plug and Lead
- 4 Flat
- 7 Round - Blade
- Hopkins
more information >
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
40 Amp In-Line Circuit Breaker - Perpendicular Mount Bracket
- Accessories and Parts
- Wiring
- Circuit Breaker
- 40 Amp
- Pollak
more information >
Product Page this Question was Asked From
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ford
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Vehicle Specific
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Shop: Adapter 4-Pole to 7-Pole and 4-Pole
- Search Results: 90160
- Article: Brake Controller Installation on a Ford Full-Size Van
- Search Results: brake systems
- Search Results: 521440~5
- Search Results: rm~522
- Search Results: brake buddy
- Search Results: 9243~1
- Search Results: rvi brake
- Shop: Base Plate for Tow Bar
- Shop: Roadmaster Falcon All-Terrain Tow Bar - Non-Binding - RV Mount - 2" Hitch - 6,000 lbs
- Shop: Roadmaster Direct-Connect Base Plate Kit - Removable Arms
- Shop: Roadmaster Accessory Kit for Falcon Tow Bars - Tail Light Wiring - Safety Cables - Lock Set
- Shop: Curt Tow Bar Extension Cord w/ Socket - Coiled - 7-Way RV to 6-Way Round - 96" Cord
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Shop: Trailer Hitch
- Shop: Deka Jacketed 2 Wire, 10 Gauge, Brake Wire - per Foot
- Q&A: Brake Controller Wiring for Ford E-450 Motorhome
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Brake Controller Wiring For 2015 Ford E450 Forester Class C Motorhome
- Q&A: Best Brake Controller for a 2016 Jayco Precept Class A Motorhome
- Q&A: Comparing the Redarc Tow-Pro Elite vs Tekonsha Prodigy P3 Brake Controller
- Video: Hayes Brake Controller HA81788-HBC Review
- Video: Redarc Tow-Pro Trailer Brake Controller Plug-and-Play Wiring Harness Review
- Video: Review of Redarc Trailer Brake Controller - Brake Controller for Tekonsha Wiring Harness - RED63RR
- Shop: Trailer Wiring
- Q&A: Brake Controller and Wiring Recommendations for RV on 2018 Ford E-450 Chassis
- Q&A: Recommended SumoSprings for a 2014 Jayco Greyhawk 31DC