Would the Uni-Lite LED Mini Utility Light # UCL11CKB Work to Illuminate Running Boards

Question

Question:

Im looking at buying these lights to use on my running boards on my truck. Will they be bright enough to make the steps visible? Im planning on putting 1 at each step.

asked by: Justin

0

Expert Reply:

The Uni-Lite LED Mini Utility Light # UCL11CKB is pretty bright. We had a customer leave a review telling us how surprised he was on how bright they are for only having two diodes. I think they would work well for illuminating running boards on a truck. I do think that maybe two per board would work better than one. But that depends on the length of the board.

I attached a review video for these lights that shows about how bright they would be.

expert reply by: Jameson C

0

Answer 1

The lumens output of the Uni-Lite LED Mini Trailer Utility Light w/ Grommet part #UCL11CKB is about 36.

view full answer...

Answer 2

To connect back up lights you need to have a 7-way trailer connector on both your trailer and tow vehicle. On a 7-way the reverse lights are powered by the center pin. To connect reverse lights to the trailer's 7-way you can use 16 gauge wire…

view full answer...

Answer 3

The Transcom #TCM 21344 TB cross references to the 10-10 seal we offer, part #RG06-090. The seal has a 2.125 inch ID and a 3.376 OD. It's compatible with a 25580 inner bearing.

view full answer...

Answer 4

Hi Eric, Airstreams typically have small tongues but if you have the space you could install the Demco Spare Tire Mount #DM15851-76. This clamps on to the trailer frame at the tongue giving you space for the hitch mounted carrier in the back. If not,…

view full answer...

Answer 5

According to the Dexter Axle instructions, the bolts that are used to install the E-Z Flex Equalizer for 1-3/4" Double Eye Springs #013-144-03 should be torqued in the range of 30 - 50 ft-lbs (see attached cutout). Attached is an installation…

view full answer...

Answer 6

The Mounting Flange for Optronics Uni-Lite Trailer Lights #A11PB can replace a rubber grommet but is made of ABS plastic so it wouldn't form a watertight seal. If your trailer needs a watertight seal then you'll need the rubber grommet for a…

view full answer...

Answer 7

With an Enclosed Trailer Ramp Spring #ERS120D81 when the door is lowered it will pull the cables which will turn the pulleys and put tension on the springs. The cables could not be detached with the ramp door lowered because the springs would…

view full answer...

Answer 8

I spoke to Command Electronics and the LED Bullet Utility Light with Grommet #328-ET003184CWM can indeed be hooked to a dimmer switch without issue. However, said dimmer switch does need to be rated for use with LED lights as not all of them are…

view full answer...

Answer 9

All of the A-frame couplers we carry are for the standard 50 degree A-frames. What you could do, since your A-frame is a lower angle, is have some steel spacers welded on to get to 50 degrees and then use a weld-on coupler. I have linked the weld-on…

view full answer...

Answer 10

On each individual electric brake magnet the amperage draw would be 3.0 to 3.2 max amps at 12 to 13 volts on 7-inch brake magnets and 3.2 to 4.0 max amps at 12 to 13 volts on 10 and 12-inch brake magnets. The max amperage draw for the brake magnets…

view full answer...

Would the Uni-Lite LED Mini Utility Light # UCL11CKB Work to Illuminate Running Boards

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching