Fuse Location for Trailer Brake Controller on a 2005 Chevy Silverado 1500

Question

Question:

where is the fuse located electris brake for chevrolet pickup 2005 1500

asked by: Randy H

0

Expert Reply:

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have included a picture that should help. I have also linked an article that will also help.

expert reply by: Michael H

0

click to enlarge

Answer 1

The Tekonsha Voyager Brake Controller with GM Wiring Harness, #39510 and #3015-P, itself does not have a fuse. Since it is connected to the truck via the factory port under the dash, the fuse for the brake controller 12 volt power is located in the…

view full answer...

Answer 2

The flicker you are seeing on the brake output circuit of your vehicle is normal. Brake controllers will lightly pulse their output circuit to check to see if a trailer is connected due to the amperage draw of the brake magnets. So what this all…

view full answer...

Answer 3

The P3 brake controller #90195 will only send back a little bit of power when just sitting so if you use the manual override on the controller then it should light up the tester solid. Using the brake pedal to test also will not work properly because…

view full answer...

Answer 4

The 7/8" Wide Trailer Coupler Latch Lock #2878DAT is made of hardened steel. As far as how easy it is to defeat, ultimately any lock can be defeated given enough time and the right tools. Since there is no gauge of how "breakeable" a…

view full answer...

Answer 5

To use the Pollak 7-Way tester part #PK12741 that you have to test the brake controller of your vehicle will require a buddy to press the brake pedal of your truck to see if the voltage from the brake controller makes it to the tester and lights up…

view full answer...

Answer 6

The Pollak 7-Way to RV Socket LED Circuit Tester #PK12741 will trick your 2022 GMC Sierra 3500 into thinking a trailer is connected as it uses the electrical connection to detect a trailer.

view full answer...

Answer 7

In regards to the Pollak 7-Way to RV Socket LED Circuit Tester part #PK12741, the brake controller may or may not read connected. This will vary from controller to controller but you should still be able to apply the override and see the light…

view full answer...

Answer 8

Have you tested the center pin of the 7-Way on your 2023 Chevy Silverado 3500 with a circuit tester like part #PK12741, or have you just been testing that circuit with your boat trailer? If you've been testing it with just your boat trailer then…

view full answer...

Answer 9

While the Pollak 7-Way to RV Socket LED Circuit Tester #PK12741 is designed to work with all 7-way connectors. There have been issues with vehicles such as Audi, Mercedes-Benz, and Volkswagen that have issues due to the LED lights having such a low…

view full answer...

Answer 10

The K-Source Custom Towing Mirrors for the 2005 Silverado that you referenced, part #KS62075-76G, are a correct fit for your truck. If the truck's current mirrors have built-in turn signals, electric adjustment and heat, then each of these…

view full answer...

Answer 11

It looks like on pages 5-126 and 5-127 or your owner's manual there is the TBC BATT fuse in the fuse box that is under the hood. This is called the Truck Body Controller Battery Feed and looks to be the only fuse title that might affect the…

view full answer...

Answer 12

You could use the brake controller part #3015-P on basically any brake controller out there but you'd have to cut off the black end of the harness and wire by color to the new controller. Normally it directly connects to Tekonsha and Draw Tite…

view full answer...

Fuse Location for Trailer Brake Controller on a 2005 Chevy Silverado 1500

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching