Installation Instructions for the TorkLift Frame-Mounted Camper Tie-Downs # TLF2014 on a Ford Truck

Question

Question:

do you have a video that shows how to install these?

asked by: Bob T

0

Expert Reply:

While we do not have an install video yet for the TorkLift Custom Frame-Mounted Camper Tie-Downs # TLF2014 on a truck like your 2013 Ford F-150 we do have a nice set of full-color installation instructions for this product that I attached to the right for you to check out.

expert reply by: Jameson C

0

Answer 1

I had our warehouse measure the Timbren Rear Suspension Enhancement #TFR1504D you were looking at for your 2014 Ford F-150, and the overall height is right at 8-5/8". With that measurement in mind and your 9" clearance, you do not need to…

view full answer...

Answer 2

The Timbren Rear Suspension Enhancement System #TFR1504D is a great product to use for your 2014 Ford F-150 XLT 4x4. It will help to support up to 8,600 lbs and you can forget about them after the installation. They come with a limited lifetime…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 6

Hey Robert, sorry it can be a bit confusing navigating all those facets for the camper tie downs, but I did go ahead and find those tie downs you were looking for. For the front, you'll want the TorkLift Camper Tie-Downs #TL87CR (TorkLift P/N…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The support braces in the HappiJac Truck-Mounted Camper Tie-Downs #LC182860 are going to attach to the cross frame to provide support for the anchors which will bolt through the bed wall and into the braces. The rear anchors will bolt through the…

view full answer...

Answer 9

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 10

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Answer 11

The 1-5/16" Hellwig Adjustable Big Wig Rear Anti-Sway Bars are designed for 2WD #HE97MR or 4WD #HE94FR versions of your 2021 Ford F-250. These are both designed for trucks which have a stock ride height. Hellwig does offer their 2" Lift…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...