What Jacks Do the Replacement Handle for Ram Jacks Fit
Question:
After watching the etrailer TJPB-HD and TJD-7000-HD videos, can you please advise the following: 1 Is the diameter of the steel the same on each handle? The length for each handle is listed in etrailers answers. 2 Are both handles shafts and mounts the same size regarding where they get mounted? Specifically, will the TJD-7000-HD handle fit on to the shaft of a TJP-7002-B or TJDP-7000, and will the TJPB-HD handle fit on to the shaft of a TJD-7000? 3 What differentiates the two handles regarding what jack they go with, because the TJP, TJDP and TJD series all have 8,000 lb. support capacity jacks, whether or not they are round or square jacks? Thank you. Kelly S.
asked by: Kelly S
Expert Reply:
Hey Kelly yes, the handle diameter is the same for both # TJPB-HD and # TJD-7000-HD and the mount for both is the same size as well. The only difference between the two handles aside from the length are the jacks they fit.
The Replacement Topwind Knob Handle for Ram Jacks # TJPB-HD specifically fits the TJA-5000T jack as well as the Ram TJB, TJP, and TJDP Series jacks.
The Replacement Topwind Handle w/ Claw Knob for etrailer and Ram Square, Direct Weld Jacks # TJD-7000-HD fits TJD-5000 and TJD-7000 Series jacks with a 3,000 - 7,000-lb capacity.
Products Referenced in This Question
Replacement Topwind Handle w/ Claw Knob for etrailer and Ram Square, Direct Weld Jacks - 3K - 7K
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Handles and Cranks
- Topwind
- etrailer
more information >
Product Page this Question was Asked From
Replacement Topwind Knob Handle for Ram Jacks
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Handles and Cranks
- Topwind
- etrailer
more information >
Continue Researching
- Shop: Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-7/8" Lift - 7,000 lbs
- Shop: Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-3/4" Lift - 3,000 lbs
- Shop: Replacement Topwind Handle w/ Claw Knob for etrailer and Ram Square, Direct Weld Jacks - 3K - 7K
- Shop: Replacement Drop Leg for etrailer and Ram Square Direct Weld Jacks - 3K
- Shop: Square Pipe Mount Swivel Jack w Footplate - Weld On - Sidewind - 15-1/4" Travel - 3,000 lbs
- Shop: Replacement Topwind Knob Handle for Ram Jacks
- Shop: Replacement Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks - 3K - 7K
- Search Results: tjdp~5000s~flb
- Search Results: jack handle
- Video: Review of etrailer Topwind Handle for Jack - TJD-7000-HD
- Video: Rebuilding the etrailer and Ram Square Jacks
- Video: etrailer Trailer Jack TJD-5000-FT Review
- Video: etrailer Trailer Jack - Side Frame Mount Jack - TJD-7000S Review
- Q&A: Diameter Of Replacement Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks
- Q&A: Replacement Drop Leg for Ram 2,500 lb Square Direct Weld Jack
- Q&A: Does the Replacement Sidewind Handle TJD-7000S-HD Have a 1/2" Diameter
- Q&A: etrailer Square Jack w/ Footplate to Replace Ram Side Wind Jack
- Q&A: What is the Correct Replacement Drop Leg for My RAM 8000 Series Trailer Jack
- Q&A: Distance from Pin Hole to End Of Handle for Winch Handle # TJD-7000S-HD
- Video: Review of Trailer Valet Trailer Jack - JXS Sidewind Trailer Jack With Adjustable Leg - TV36FR
- Article: Tire TLC: How & When to Check Your RV/Trailer Tire Pressure
- Shop: Trailer Hitch
- Search Results: 44649
- Shop: Trailer Wiring
- Video: Choosing the Right Trailer Wiring
- Search Results: swivel jack
- Video: Optronics 7-Way Trailer Harness Plug Protector Installation
- Shop: Fifth Wheel Hitch
- Search Results: dust cap
- Search Results: 25580
on Accessories and Parts
Kelly S.
5/8/2024
Bryce, if the diameters are the same and assuming that the materials are, too, are you saying then that the TJD-7000-HD handle just won't fit the shaft of the TJB, TJP and TJDP, and that the TJPB-HD handle won't fit the TJD shaft? In other words, if the handles are identical with the exception of the lengths, is it physically possible to fit both of these handles on any one of the topwind jacks in the TJP, TJDP and TJD series? Since the TJD-7000-HD doesn't seem to be more heavy duty, I am trying to determine why one handle fits some of the jacks but not the other. Thank you. Kelly S.