Will the EZ Coupler Sewer Hoses w/ Swivel Lug Fittings Fit Inside the Valterra Sewer Hose Carrier?

Question

Question:

Re: D04-0115 hose and 90foot coupler - do you know if the 90 elbow will fit in the Valterra Hose carrier which is 4 1/2 ID according to your reply to a viewers questions. I have searched all questions/reviews and do not see where this has been queried - thank you for your time.

asked by: Jamie J

0

Expert Reply:

No, the elbow won't fit but if you take it off the EZ Coupler RV Sewer Hoses w/ Swivel Lug Fittings item # D04-0115 will fit inside the Valterra RV Sewer Hose Carrier item # A04-5094BK. The fittings measure right at 4-3/16" so you'll have just enough room without the elbow attached.

expert reply by: Jerred H

0

Answer 1

I went out to the warehouse to measure the overall depth of the Valterra Twist-On Waster Valve, #T58, for you. It has an overall depth of 5-1/16 inches. I have included a picture showing this for you.

view full answer...

Answer 2

The 90 degree portion of the EZ Coupler RV Sewer Hose Kit #D04-0115 is a separate piece but the part that fits in the dump station inlet is attached to it. I included a picture showing this close up.

view full answer...

Answer 3

The max length of a compressed hose that could fit in the Valterra EZ RV Sewer Hose Carrier #A04-0150XBK is 26 inches. The inner diameter is 4-3/8 inches. This carrier is designed to fit the style of hoses that use the bayonet fittings.

view full answer...

Answer 4

The inner diameter of the #A04-5094BK is 4-1/2 inches. This is the diameter of available space for storage.

view full answer...

Answer 5

I measured the fittings on the EZ Coupler RV Sewer Hose Kit #D04-0115 for you. On either end the overall diameter at the widest point is 4.15 to 4.16 inches. That is a hair under 4-3/16 inches.

view full answer...

Answer 6

For replacement gaskets for the bayonet side of the Valterra fitting #T1028 you'd want to use the part #CAM39834.

view full answer...

Answer 7

Based on the photo you sent in it looks like someone glued on a piece that isn't going to allow you to use a standard waste hose. The solution to this issue would be to remove the waste valve and replace it with another that is compatible with a…

view full answer...

Answer 8

The depth of the Valterra Waste Valve for RV Black Water Tank part #T50A measures 4-1/4" end to end without the cap but please note the fittings don't butt up to the end on either side.

view full answer...

Answer 9

If you look at the third bracket you can see that it wraps around the tube far enough to actually hold it and not just let it fall. The tube's overall weight is pretty low so it would not want to just fall out.

view full answer...

Answer 10

It is completely within the realm of possibilities that the actuator has become disconnected from the gate internally causing the valve to not open. The Valterra Waste Valve Body for RV Black Water Tank w/ Coupler, Seals, and Hardware - 3"…

view full answer...

Answer 11

While we have an option for you, both of the hoses from the EZ Coupler RV Sewer Hose Kit - (2) 10' Long Hoses #D04-0115 will be 50 inches when collapsed, which is too long for your 4 foot bumper. You can use one of the 10 foot hoses, the EZ…

view full answer...