Will Dexter Idler Hub for 12k Axles Fit Lippert Axle

Question

Question:

Do you use the same idler hub for Dexter and Lippert 12,000 lb axles. Have a diamond sea trailer did the Kodiak conversion brakes disc brake system and need new studs for The Idler hub. For now just want to get a new idler hub thatll fit a 12,000 lb Lippert axle

asked by: Joey

0

Expert Reply:

More than likely your Lippert axle uses the standard # 3984 inner and # 28682 outer bearing. I would double check to be sure. Assuming that is correct, the Dexter Trailer Idler Hub Assembly for 12,000-lb Axles # 8-214-8UC1 will fit.

expert reply by: Robin H

0

Answer 1

The Replacement Trailer Hub Bearing #3984 has an inner diameter of 2.625", so it's possible that it will work on your 12,000-lbs Dexter axle, but you'll need to know what bearings are in your hubs to confirm this is the correct…

view full answer...

Answer 2

Yes, the Dexter Trailer Idler Hub Assembly for 12,000-lb Axles - 8 on 6-1/2 - Oil Bath #8-214-8UC1 will work with disc brakes.

view full answer...

Answer 3

We don't have the length of stud you are seeking. The longest 5/8 inch stud we have is 3-1/8 inches. If that length will work, I recommend the Replacement Trailer Hub Wheel Stud, Drive-In, 5/8" x 3-1/8" (Qty 4) #RG03-120. These are a…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 9

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 10

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Answer 11

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Will Dexter Idler Hub for 12k Axles Fit Lippert Axle

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching