Powered Camper Jack Recommendation for 8 foot Alaskan Truck Camper

Question

Question:

Can i get electric jacks for 8’ slaskan camper ? I have rico jacks, can they be vonverted to electric? Thank you gor the help

asked by: Jude H

0

Expert Reply:

There isn't a way to convert the manual jacks you have on your camper now to electric so your best option would be to go with the HappiJac electric camper jack system part # LC736514-ELKIT to give you a powered jack system that would work great on your 8 foot Alaskan camper.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 6

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 7

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…

view full answer...

Answer 8

There is a way for you to not only lock the B&W Tow & Stow 3-Ball Mount - Compatible with GM MultiPro Tailgate - 2.5" Hitch - 148K #BWTS20067BMP to your 2-1/2 inch trailer hitch, but also the ball platform to the mount, and the hitch…

view full answer...

Answer 9

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 10

I recommend using the Curt Lock Set #C23556 for your Curt Adjustable 2-Ball Mount #C99NR. This comes with a lock for the hitch receiver and one for the ball mount platform. Even though your platform uses 2 pins, only 1 locking pin is needed to secure…

view full answer...

Answer 11

The B&W Tow and Stow ball mount #BWTS10049B will have some great features. You can stow the mounting platform that has the 3 hitch balls (1-7/8, 2, and 2-5/16 inch) underneath your vehicle. This is nice because you will eliminate the possibility…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Powered Camper Jack Recommendation for 8 foot Alaskan Truck Camper

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching