Does Erickson Over the Cab Ladder Rack Fit 2022 Ram 2500 Long Bed Crew Cab

Question

Question:

Will this fit and 8 ft bed and a crew cab

asked by: James B

0

Expert Reply:

Hey James, yes the Erickson Over the Cab Ladder Rack part # EM07707 that you referenced is a confirmed fit for your 2022 Ram 2500 long bed crew cab.

expert reply by: Jameson C

0

Answer 1

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 2

No, they will not but I have a custom fit set that does. They are the Curt item #C16427-204. This set of rails is industry standard so they will work great with your Curt Q20 Slider. The brackets are custom fit and install in pre-existing holes in…

view full answer...

Answer 3

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 4

Yes, the Voyager WiSight 2.0 Wireless RV Backup Camera #ASA84YR will have consistent signal with your setup. The camera and monitor both have a wireless range of 60 feet or more. So even with about 52' between them, you will be well within…

view full answer...

Answer 5

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 6

I have some good news for you. The B&W Patriot 5th wheel trailer hitch #BWRVK3270 fits in industry standard above the bed rails. If your rails have mounting slots on the tops that are spaced like those in the picture I have included then the…

view full answer...

Answer 7

The Gen-Y Hitch 5th Wheel to Gooseneck Pin Box part #GY58GR is primarily designed for long bed trucks. It's no different than a standard fifth wheel pin box in regards to the size. If you were using a fixed hitch and standard pin box before with…

view full answer...

Answer 8

The correct replacement motor for your Atwood mpd71113 is the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor #LC141893. The Atwood mpd71113 was discontinued. We have contacted the manufacturer about a replacement for the Atwood…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 11

The Patriot Slider part #BWRVK3270 might be a bit more noisy than the Companion slider part #BWRVK3400 due to the increased number of mounting points, 4 at the corners vs. 1 in the center. Probably not that noticeable and certainly not something…

view full answer...

Answer 12

It sounds like you could have a set of standard fifth wheel rails that most manufacturers use for their fifth wheel hitches to install into. The different manufacturers all make their own brand of rail kit, but they all have basically the same…

view full answer...

Does Erickson Over the Cab Ladder Rack Fit 2022 Ram 2500 Long Bed Crew Cab

Product Page this Question was Asked From

Continue Researching