What Size Hole Needs To Be Drilled For a 2" Round Recessed Trailer Marker Light?

Question

Question:

what size hole to drill for 2 in. marker light with rubber grommet ?

asked by: James K

0

Expert Reply:

The Optronics LED Trailer Clearance or Side Marker Light # MCL55AB fits with a Grommet # A54GB into a 2-5/16" mounting hole.

expert reply by: Bud M

0

Answer 1

The easiest way to cut the oval hole for the Rubber Grommet, #a70gb, in my opinion, would be to use a Light Mounting Bracket for 6-1/2 inch Oval Trailer Lights, BK70BB, as a template and then use a hole saw the correct size to cut a hole on each end…

view full answer...

Answer 2

We have determined that you would need an 11/16 inch hole for a tight fit when installing Sealed, Uni-Lite Mini LED Side Marker and Clearance Light #MCL11RKB. A 3/4 inch hole could work but it would be slightly looser.

view full answer...

Answer 3

The Optronics LED Trailer Tail light - Stop, Tail, Turn - Submersible - 10 Diodes - Red Lens #STL72RB will use the PVC Grommet for 6-1/2" Oval Trailer Tail Lights #A70GB for mounting. With this combination the opening you need to cut is a…

view full answer...

Answer 4

The LED Trailer Mini Clearance and Side Marker Light with Grommet #MCL10AKB will fit best with a wall (or bracket) thickness that is just under 5/16".

view full answer...

Answer 5

I spoke with my contact at Optronics and was informed that the Lumen Difference between the #STL22RB and the #STL72RB LED tail lights is not tested by Optronics. I was told though that the more LED lights that are in the tail light the brighter the…

view full answer...

Answer 6

If your tail lights look like #STL16RB or #STL17RB, then you can use the Replacement Tail Light Lens, #A16RB.

view full answer...

Answer 7

To install the Sealed, 4" Round LED Trailer Stop, Turn and Tail Light, Flange Mount Light #STL42RB that you referenced you will need to drill a 4-1/2 inch hole for the light to fit and the mounting holes will be 4-1/4 inches apart on center. For…

view full answer...

Answer 8

The Optronics Fleet LED Trailer Tail Lights w/ Grommets #TLL12RK has grommets that are 1-1/8 inches deep. The plate dimension if you want to use the integrated lip on the grommet is 3/16 inch and if not is up to 1/2 inch. I went out to our warehouse…

view full answer...

Answer 9

I went out to the warehouse and pulled a #BK70BB bracket, a 6 inch oval tail light and the A70GB grommet. I found that it is much easier to install everything if you push the grommet fully into the bracket until it is fully seated and then push the…

view full answer...

Answer 10

Metal that is 1/4 inch thick will work well for the round grommet #A55GB. There isn't a specific metal thickness requirement for the grommet since the light pushing against it when installed is what holds the whole assembly in place.

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

What Size Hole Needs To Be Drilled For a 2" Round Recessed Trailer Marker Light?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching