Amperage Draw Of A Furrion Vision S RV Camera System Monitor

Question

Question:

How many amps does the furrion s monitor pull off a 12 volt dc power supply model # fos43tads?

asked by: John

0

Expert Reply:

The 4.3" Furrion Vision S Camera System monitor # FR77FR is going to pull 500mA at 12v when the screen back light is on and 300mA at 12v when the light is off.

expert reply by: Kevin C

0

Answer 1

Yes you can use the AC to DC Adapter for Swift Hitch Wireless Camera System part #PP01 to get your 115 AC power down to the 12V power that you require for your Furrion monitor to work. As an alternative and more permanent type of fix for this you…

view full answer...

Answer 2

There is not another way to power the monitor on your Voyager WiSight 2.0 so you'll need to add one with the 12 Volt Outlet Kit, 20 amps #RM-9332. This kit is going to add a 12V cigarette lighter to your 2024 GMC Sierra 2500 and will allow…

view full answer...

Answer 3

There are adapters on the market that can go from a cigarette lighter style plug that the #C-FOS07TAPK-006 has to USB/USB-C ports but we don't currently offer any so the only solution I can provide is the #RM-9332. This is a replacement…

view full answer...

Answer 4

Currently the only power cord available for the Furrion Vision S camera systems is the Furrion Monitor Power Cable #C-FOS07TAPK-006, which uses that 12v cigarette style port. We do not have an adapter specifically for this power cable, but I do have…

view full answer...

Answer 5

The issue that you're facing with your Furrion camera System is caused by the PWM GM has switched to with their 7-way wiring and can be solved in two ways: 1. By using the 7-Way Vehicle Power Adapter w/ Power Switch for Furrion RV Observation…

view full answer...

Answer 6

I took a look at the instruction manual for the Furrion Vision S Wireless RV Backup Camera System part #FOS43TASF which is attached below as well and there are a few possible causes of the weak/intermittent signal issues you are experiencing. I have…

view full answer...

Answer 7

The Furrion Vision S Wireless RV Backup Camera System w/ Night Vision - Rear Mount - 4.3" Screen #FOS43TASF sounds like it simply has electrical interference or has obstructions causing that weak signal. You may want to replace the antenna with…

view full answer...

Answer 8

Yes, the Furrion power cord part #C-FOS07TAPK-006 that you referenced does fit the 5 inch monitor version of the Furrion Vision S part #FOS05TASF.

view full answer...

Answer 9

The Monitor for your Furrion Vision S wireless Rv Backup Camera part #FOS43TASF is meant to come on as soon as it has a 12V power source. Some vehicles only power on the 12 volt accessory outlet when the vehicle is running; you want to check that…

view full answer...

Answer 10

Since the GM TPMS uses a proprietary software so you aren't going to be able to use another sensor with the program even if they operate on the same frequency. So, with that being said, your best option is to use a standalone system like the TST…

view full answer...

Answer 11

The new GM trucks are a little more challenging to use the Furrion Vision S camera systems like the part #FOS43TASF that you referenced but we have easy solutions that fix the problem. For a plug in adapter that installs inline with your 7-way…

view full answer...

Answer 12

The recommendation for the 10" diameter lube plate on a B&W Companion 5th Wheel Trailer has come from the manufacturer of the fifth wheel hitch, B&W. The Lube Plate for Reese 5th Wheel Trailer Hitches part #RP83002 will work just fine…

view full answer...

Amperage Draw Of A Furrion Vision S RV Camera System Monitor

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching