Correct Replacement Tonneau Cover for a TruXedo Lo Pro Tonneau On a 2013 Ford F-250

Question

Question:

I am looking for a Tonneau Cover Replacement. Just the cover. Low Pro QT Date Code 5691 08 *1312 Could not find the serial number. 7 th digit was unreadable so I used an *

asked by: Bruce A

0

Expert Reply:

For your TruXedo Lo Pro Soft Roll-up Tonneau Cover # TX569101 you'll just need the Replacement Cover for TruXedo Lo Pro Soft, Roll-up Tonneau Cover # TX569101-CVR for a replacement cover.

expert reply by: Bryce D

0

Answer 1

Thanks for all of the info on the tonneau cover of your 2012 Ford F-250 short bed. For a replacement you'd just need the part #TX569101-CVR.

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 4

The Curt CrossWing Lightweight 5th Wheel Trailer Hitch item #C86JR weighs only 60 lbs. This is the one that mounts to industry standard 5th wheel rails. I have linked a review video below so you can see the functions of this hitch demonstrated.

view full answer...

Answer 5

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The BAKFlip MX4 Tonneau Cover #BAK48330 for the 2022 F-250 short bed has 4 panels. While you are using your Demco Autoslide 5th Wheel Hitch #DM8550024 you will be able to keep one panel laying flat on the bed. There are tow ways you can store the…

view full answer...

Answer 9

The Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs #F95FV will be just fine if you need to lift your 2022 Ford F-250 Super Duty, but it will be good practice to lower the psi rating to 5 prior to lifting the truck. I confirmed this…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Correct Replacement Tonneau Cover for a TruXedo Lo Pro Tonneau On a 2013 Ford F-250

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching