How to Connect Power Cord on Thomas Payne Seismic Recliner Set

Question

Question:

How do you connect the power cords on seismic recliner set

asked by: Wade

0

Expert Reply:

Behind the Thomas Payne Seismic Recliners there are power connections on either end. These are located near the edges of the recliners near the bottom (see attached photo "C" connections).

You'll simply push the Replacement Power Cord with Power Supply Box # 195-000111 connector into place and secure it with the flip bracket. Be sure to do this prior to plugging the box into the wall though.

expert reply by: Jon G

0

Loveseat Wiring
(click to enlarge)

Answer 1

We offer a range of 2-step electric step assemblies for motorhomes like your 1986 Winnebago Chieftain 27 that are displayed on the linked page. These are available in three different widths: 24-inch, 26-1/4-inch and 30-inch. Based on photos of this…

view full answer...

Answer 2

You will only need one Replacement Power Cord with Power Supply Box for Thomas Payne Seismic RV Power Reclining Sofas #195-000111 for your sofa as both sides are connected electrically during assembly.

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

How to Connect Power Cord on Thomas Payne Seismic Recliner Set

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching