Can Holes be Drilled in UWS A-Frame Trailer Toolbox

Question

Question:

I am looking at this to replace a current plastic- open bottom box that holds my RV battery just one deep cycle and one propane tank. I read the answer about venting- could holes be drilled in the back or bottom of the box to allow for venting? My concerns are thieves, bees and critters.

asked by: Bonnie S

1

Helpful Expert Reply:

Yes, you could drill holes in the UWS A-Frame tool box part # UWS01039 to allow for venting or battery lines ran to it like you asked about.

expert reply by: Jameson C

1

Answer 1

I am happy to help you find a trailer tongue tool box for your Sure Trac trailer Andy. When you say you have 44 inches from the widest point, I believe you are referring to 44 inches up from the widest point of the A-frame towards the tailgate. You…

view full answer...

Answer 2

UWS recommends to use U-bolts to secure the A-Frame Trailer Toolbox #UWS01039 to the front of the trailer. As there are several different frame sizes on trailers you will want to select the correct size U-bolts to fit your frame. Be sure to account…

view full answer...

Answer 3

I was not able to find any ballard winches, but perhaps you mean Badland winch? I looked at the owner's manual for the Badland 9000lb truck/suv winch and they recommend a battery with a minimum of 650 cold cranking amps (CCA). If you are hooking…

view full answer...

Answer 4

These toolboxes do not contain mounting hardware due to the different construction and mounting locations that may be required for many different styles of trailers. A lot of how you install the UWS A-Frame Trailer Toolbox #UWS01065 depends on where…

view full answer...

Answer 5

We have the UWS A-Frame Trailer Toolbox part #UWS01065 which is 49 inches wide at the rear and 18 inches in the front.

view full answer...

Answer 6

The RC Manufacturing T-Series Trailer Tongue Toolbox - A-Frame - Steel #313-TM362016M is just the steel box. Most people drill into the bottom of the box to hold the box to the trailer frame with self-tapping screws like #WLS100. You can weld it if…

view full answer...

Answer 7

The Buyers Products Trailer Tongue Toolbox part #3371701680 does not come with mounting hardware. It can be secured in a number of different ways, most drill directly though the bottom of the box and into the frame. If you can find a way to mount the…

view full answer...

Answer 8

Although none of the trailer tongue toolboxes we offer precisely meets the measurements you provided, we have options that could work for you. The most obvious choice and what I'd recommend would be the UWS #UWS01039 box you'd looked at. At…

view full answer...

Answer 9

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Can Holes be Drilled in UWS A-Frame Trailer Toolbox

Product Page this Question was Asked From

Continue Researching